Minimum Headroom Height
From How to Check Your Stairs Against Building Code · Step 9 of 10 · Video by gregvancom

Showing 2:19–2:52 of the source video. Watch the full video with every moment.
What happens in this clip
Understand the minimum headroom height requirement for stairways, which must be not less than 6 feet 8 inches. This measurement is taken vertically (plumb or perfectly level) from a specific point: the line representing the front of each step (the nosing line). It is important not to measure from the top surface of the step or any other part of the step, but consistently from this leading edge line upwards.
Goal: Achieve adequate headroom clearance (6' 8") above stairs.
What's used
Tools
- Plumb Bob
- Tape Measure
About the full video
This project offers a comprehensive guide for DIY enthusiasts on essential stair building codes based on the 2021/2022 International Residential Building Code. It systematically breaks down regulations concerning door swings over stairs, minimum stairway width, required headroom clearance, individual riser height limits, minimum tread depth, landing dimensions, allowable variations in riser and tread measurements, and exceptions for non-habitable attic and crawl space access. The goal is to provide a solid foundation of knowledge for planning and executing safe and compliant stair construction or renovation projects.
What's said in this clip
Like drywall wood trim or skirt board. Next up on the list will be the minimum headroom height and that line will be measured from this line here or the front of each step, but it will not be measured from the top of the step on any other part of the step. Again, it's going to be measured from this line here. You're going to go straight up plumb or vertically level and again, it can be measured from the front of each step or from this line here. Next up will be the individual vertical rise that will be a maximum it cannot be larger than seven and three quarters of an inch.
Automatically transcribed from the source video.
Step 9 of 10: Check Headroom
Measure the vertical distance from the top of the stair tread (or landing) to the lowest obstruction above it (e.g., ceiling, beam, light fixture). Building codes typically require a minimum headroom of 80 inches (6 feet 8 inches) throughout the entire stair and landing area.
Every video in How to Check Your Stairs Against Building Code
Step 1: Measure Stair Rise
Step 2: Measure Stair Run
- 0:42–0:56 Measure and Verify Rise and Run
- 0:52–2:34 Measuring Rise and Run
- 2:00–2:24 Analyzing Stairway with Consistent Nosings (Correct Design)
Step 3: Check for Consistent Riser Height
- 0:31–1:01 Measure Riser Height and Tread Depth Consistency
- 4:28–6:49 Maximum Riser and Tread Difference
- 3:09–3:40 Set Riser Height and Consistency
Step 4: Check for Consistent Tread Depth (Run)
Step 5: Inspect Tread Nosing
Step 6: Check Stair Width
- 1:36–2:19 Minimum Stairway Width
- 1:34–2:22 Determine Overall Stair Width
- 0:00–0:40 Understand Minimum Stairway Width
Step 7: Inspect Handrails
- 0:24–0:42 Check Railing Height
- 4:07–4:38 Inspect Commercial Stair Handrails
- 1:50–2:05 Measure Handrail Height
Step 8: Inspect Balusters and Guardrails
- 5:28–6:08 Check Guardrail Openings
- 0:29–0:58 Measure Baluster Spacing for Code Compliance
- 0:25–0:29 Check Guardrail Opening Size
Step 9: Check Headroom
- 2:19–2:52 Minimum Headroom Height (this video)
- 0:40–1:12 Determine Minimum Headroom Height
- 10:28–12:22 Verify Fitment and Headroom in Space
Step 10: Evaluate Landing Requirements
- 12:40–15:25 Understand Landing Code Requirements
- 17:28–23:43 Identify Landing Size Requirements
- 6:03–6:46 Implement Landings
Questions about How to Check Your Stairs Against Building Code
Why do I need both a dial caliper and a pocket caliper, and what are they used for?
These specialized tools are crucial for precise measurements of small details like tread nosing projection and baluster spacing, which often have tight code tolerances. While a tape measure handles overall dimensions, calipers ensure the accuracy needed for these critical, smaller elements to confirm compliance.
What safety precautions should I take while inspecting my stairs?
Ensure the staircase is well-lit to clearly see all features and potential hazards. Be cautious if treads feel loose, handrails are wobbly, or if there are any obvious signs of structural instability. Do not attempt repairs during inspection; simply identify issues.
Is the 4-hour estimate realistic for a beginner, or could this project take longer?
The 4-hour estimate is a general guideline for an average straight staircase. If you have multiple flights, complex turns, or find yourself needing to re-measure for accuracy, it could take longer. Take your time to ensure all measurements are precise.
What are the most common building code violations people overlook when checking stairs?
Many people miss inconsistencies in riser height or tread depth, even by small fractions, which are significant tripping hazards. Other common issues include improper handrail height or grip, baluster spacing wider than 4 inches, and insufficient headroom clearance.
What should I do if my existing stairs don't meet current building codes?
Document all identified violations with measurements and photos. Prioritize immediate safety hazards. For significant issues, consult with a licensed contractor or your local building department to understand the necessary steps and potential costs for bringing your stairs up to code.
How to Check Your Stairs Against Building Code
This project outlines the process for a DIYer to check their existing stairs against common building code requirements. It involves understanding key measurements and features of stairs and comparing them to established standards. The goal is to identify any potential safety issues or code violations.
Read the full guide Browse all guides
Planning this project? Shop Oak Valley Designs.

