powered by

Measure Riser Height and Tread Depth Consistency

From How to Check Your Stairs Against Building Code · Step 1 of 10 · Video by stairbuilding

Showing 0:31–1:01 of the source video. Watch the full video with every moment.

What happens in this clip

To perform a precise measurement, take a framing square and position it firmly against the riser and tread of a step. Place the short arm of the square on the tread and the long arm vertically against the riser above it. Note the measurement at the top of the riser. Then, position the long arm of the square along the tread, extending towards the front edge (nosing) of the step, and the short arm vertically against the riser of the step below. Note the measurement for the tread depth. Repeat this process for every step on the staircase. The purpose is to compare the measurements for each riser and tread, ensuring they are consistent throughout the staircase. The video demonstrates this technique on a theoretically perfect staircase to show expected uniformity.

Goal: Utilize a framing square to accurately measure the riser height and tread depth at multiple points on each step, checking for consistency and any variations.

What's used

Tools

  • Framing Square

About the full video

This video illustrates how to perform a visual and measurement-based inspection of older staircases to identify wear and tear that could result in building code violations related to riser height and tread depth. It emphasizes the importance of checking for consistency between steps to ensure safety and compliance, particularly for homeowners undertaking remodeling projects. While the requested context was Electrical Code Compliance, this video specifically addresses structural building codes for stairways.

Step 1 of 10: Measure Stair Rise

Using a tape measure, accurately record the vertical distance from the top surface of one tread to the top surface of the adjacent tread. This measurement is known as the stair rise. Repeat this for every step to check for uniformity. Building codes typically require stair rises to be between 4 inches and 7 inches, and all rises within a single flight of stairs should be within 3/8 inch of each other.

Open this step in the guide

Every video in How to Check Your Stairs Against Building Code

  1. Step 1: Measure Stair Rise

  2. Step 2: Measure Stair Run

  3. Step 3: Check for Consistent Riser Height

  4. Step 4: Check for Consistent Tread Depth (Run)

  5. Step 5: Inspect Tread Nosing

  6. Step 6: Check Stair Width

  7. Step 7: Inspect Handrails

  8. Step 8: Inspect Balusters and Guardrails

  9. Step 9: Check Headroom

  10. Step 10: Evaluate Landing Requirements

Questions about How to Check Your Stairs Against Building Code

Why do I need both a dial caliper and a pocket caliper, and what are they used for?

These specialized tools are crucial for precise measurements of small details like tread nosing projection and baluster spacing, which often have tight code tolerances. While a tape measure handles overall dimensions, calipers ensure the accuracy needed for these critical, smaller elements to confirm compliance.

What safety precautions should I take while inspecting my stairs?

Ensure the staircase is well-lit to clearly see all features and potential hazards. Be cautious if treads feel loose, handrails are wobbly, or if there are any obvious signs of structural instability. Do not attempt repairs during inspection; simply identify issues.

Is the 4-hour estimate realistic for a beginner, or could this project take longer?

The 4-hour estimate is a general guideline for an average straight staircase. If you have multiple flights, complex turns, or find yourself needing to re-measure for accuracy, it could take longer. Take your time to ensure all measurements are precise.

What are the most common building code violations people overlook when checking stairs?

Many people miss inconsistencies in riser height or tread depth, even by small fractions, which are significant tripping hazards. Other common issues include improper handrail height or grip, baluster spacing wider than 4 inches, and insufficient headroom clearance.

What should I do if my existing stairs don't meet current building codes?

Document all identified violations with measurements and photos. Prioritize immediate safety hazards. For significant issues, consult with a licensed contractor or your local building department to understand the necessary steps and potential costs for bringing your stairs up to code.

How to Check Your Stairs Against Building Code

This project outlines the process for a DIYer to check their existing stairs against common building code requirements. It involves understanding key measurements and features of stairs and comparing them to established standards. The goal is to identify any potential safety issues or code violations.

Read the full guide Browse all guides

Planning this project? Shop Oak Valley Designs.

Measure Riser Height and Tread Depth Consistency — How to Check Your Stairs Against Building Code | Oak Valley Designs

Subscribe for exclusive updates

Be the first to know about promotions, new products, and sales.