Measure Tread Depth on Standard Passenger Tires
From How to Check Your Stairs Against Building Code · Step 4 of 10 · Video by Danny Johnson’s Garage

Showing 0:08–0:51 of the source video. Watch the full video with every moment.
What happens in this clip
Utilize a tire tread depth gauge to accurately measure the remaining tread on your standard passenger tires. To get a reliable reading, insert the probe of the gauge into the deepest part of a major tread groove, ensuring that the base of the gauge rests firmly and flat across two adjacent tread blocks. It's crucial to take multiple measurements across the width of the tire's tread to check for even wear. Measure at a minimum of three distinct points: the outer edge, the center, and the inner edge of the tread. The video demonstrates this process, showing readings of approximately 7/32nds of an inch on the outer edge, 5/32nds in the middle, and 6/32nds on the inner edge of the tire. Compare these measured depths against the legal minimum tread depth (which is typically 2/32nds of an inch in many regions) and any specific recommendations from your tire manufacturer or vehicle's owner's manual for optimal safety and performance.
Goal: Determine the remaining usable tread on standard passenger vehicle tires.
What's used
Tools
- Tire Tread Depth Gauge
About the full video
This project provides a comprehensive guide on how to perform a DIY inspection of your vehicle's tires. It covers identifying common issues like dry rot, accurately measuring tread depth using a tread depth gauge, and understanding specialized tire characteristics such as those of drag radials. Additionally, the guide explains how to locate and interpret the Uniform Tire Quality Grading (UTQG) treadwear rating found on tire sidewalls, helping you assess tire longevity and performance characteristics.
What's said in this clip
sun. So, it's really not too bad on tread depth per se. This particular tire here. A little bit over 6 32nds. And then in the middle 5 32nds. And then on the other edge And about the 6 32nds again. So, not horrible but uh definitely just this brand of tire looks like it's prone to some dry rotting.
Automatically transcribed from the source video.
Step 4 of 10: Check for Consistent Tread Depth (Run)
Review the tread run measurements from Step 2. While codes primarily focus on riser consistency, consistent tread depth is also important for user comfort and safety. Ensure each tread provides adequate foot placement. Check that the 'going' (horizontal distance from the face of one riser to the face of the next) meets the minimum requirement, typically 10 inches.
Every video in How to Check Your Stairs Against Building Code
Step 1: Measure Stair Rise
Step 2: Measure Stair Run
- 0:42–0:56 Measure and Verify Rise and Run
- 0:52–2:34 Measuring Rise and Run
- 2:00–2:24 Analyzing Stairway with Consistent Nosings (Correct Design)
Step 3: Check for Consistent Riser Height
- 0:31–1:01 Measure Riser Height and Tread Depth Consistency
- 4:28–6:49 Maximum Riser and Tread Difference
- 3:09–3:40 Set Riser Height and Consistency
Step 4: Check for Consistent Tread Depth (Run)
- 0:08–0:51 Measure Tread Depth on Standard Passenger Tires (this video)
Step 5: Inspect Tread Nosing
Step 6: Check Stair Width
- 1:36–2:19 Minimum Stairway Width
- 1:34–2:22 Determine Overall Stair Width
- 0:00–0:40 Understand Minimum Stairway Width
Step 7: Inspect Handrails
- 0:24–0:42 Check Railing Height
- 4:07–4:38 Inspect Commercial Stair Handrails
- 1:50–2:05 Measure Handrail Height
Step 8: Inspect Balusters and Guardrails
- 5:28–6:08 Check Guardrail Openings
- 0:29–0:58 Measure Baluster Spacing for Code Compliance
- 0:25–0:29 Check Guardrail Opening Size
Step 9: Check Headroom
- 2:19–2:52 Minimum Headroom Height
- 0:40–1:12 Determine Minimum Headroom Height
- 10:28–12:22 Verify Fitment and Headroom in Space
Step 10: Evaluate Landing Requirements
- 12:40–15:25 Understand Landing Code Requirements
- 17:28–23:43 Identify Landing Size Requirements
- 6:03–6:46 Implement Landings
How to Check Your Stairs Against Building Code
This project outlines the process for a DIYer to check their existing stairs against common building code requirements. It involves understanding key measurements and features of stairs and comparing them to established standards. The goal is to identify any potential safety issues or code violations.
Read the full guide Browse all guides
Planning this project? Shop Oak Valley Designs.

