Analyzing Stairway with Consistent Nosings (Correct Design)
From How to Check Your Stairs Against Building Code · Step 2 of 10 · Video by stairbuilding

Showing 2:00–2:24 of the source video. Watch the full video with every moment.
What happens in this clip
This step demonstrates a correctly designed stairway where all steps, including the connection to the upper deck, uniformly feature a 1-inch nosing. Each tread depth is consistently 11 inches, measured from the front of the nosing on one step to the front of the nosing on the step below. This design adheres to building codes for consistent tread depth, ensuring safety and compliance.
Goal: Understand the correct stairway design with consistent nosings for all steps and the deck.
What's used
Tools
- 3D Modeling Software
About the full video
This video illustrates common construction errors in stairway design, focusing on tread depth measurements and the use of nosings. It highlights how inconsistencies can lead to code violations and potential safety hazards, offering insights into correct and incorrect approaches.
Step 2 of 10: Measure Stair Run
Measure the horizontal distance from the leading edge of one tread to the leading edge of the next tread. This measurement is the stair run. Ensure that the run is consistent across all steps. Building codes typically require a minimum stair run of 10 inches for residential stairs. The 'tread depth' (the part you step on) is typically measured from the nosing of one step to the nosing of the next. Codes usually specify a minimum tread depth (e.g., 10 inches), and the 'going' (the horizontal distance from one riser to the next) should not exceed the tread depth.
Every video in How to Check Your Stairs Against Building Code
Step 1: Measure Stair Rise
Step 2: Measure Stair Run
- 0:42–0:56 Measure and Verify Rise and Run
- 0:52–2:34 Measuring Rise and Run
- 2:00–2:24 Analyzing Stairway with Consistent Nosings (Correct Design) (this video)
Step 3: Check for Consistent Riser Height
- 0:31–1:01 Measure Riser Height and Tread Depth Consistency
- 4:28–6:49 Maximum Riser and Tread Difference
- 3:09–3:40 Set Riser Height and Consistency
Step 4: Check for Consistent Tread Depth (Run)
Step 5: Inspect Tread Nosing
Step 6: Check Stair Width
- 1:36–2:19 Minimum Stairway Width
- 1:34–2:22 Determine Overall Stair Width
- 0:00–0:40 Understand Minimum Stairway Width
Step 7: Inspect Handrails
- 0:24–0:42 Check Railing Height
- 4:07–4:38 Inspect Commercial Stair Handrails
- 1:50–2:05 Measure Handrail Height
Step 8: Inspect Balusters and Guardrails
- 5:28–6:08 Check Guardrail Openings
- 0:29–0:58 Measure Baluster Spacing for Code Compliance
- 0:25–0:29 Check Guardrail Opening Size
Step 9: Check Headroom
- 2:19–2:52 Minimum Headroom Height
- 0:40–1:12 Determine Minimum Headroom Height
- 10:28–12:22 Verify Fitment and Headroom in Space
Step 10: Evaluate Landing Requirements
- 12:40–15:25 Understand Landing Code Requirements
- 17:28–23:43 Identify Landing Size Requirements
- 6:03–6:46 Implement Landings
How to Check Your Stairs Against Building Code
This project outlines the process for a DIYer to check their existing stairs against common building code requirements. It involves understanding key measurements and features of stairs and comparing them to established standards. The goal is to identify any potential safety issues or code violations.
Read the full guide Browse all guides
Planning this project? Shop Oak Valley Designs.

