Measure Riser Height and Tread Depth Consistency
From How to Check Your Stairs Against Building Code · Step 3 of 10 · Video by stairbuilding

Showing 0:31–1:01 of the source video. Watch the full video with every moment.
What happens in this clip
To perform a precise measurement, take a framing square and position it firmly against the riser and tread of a step. Place the short arm of the square on the tread and the long arm vertically against the riser above it. Note the measurement at the top of the riser. Then, position the long arm of the square along the tread, extending towards the front edge (nosing) of the step, and the short arm vertically against the riser of the step below. Note the measurement for the tread depth. Repeat this process for every step on the staircase. The purpose is to compare the measurements for each riser and tread, ensuring they are consistent throughout the staircase. The video demonstrates this technique on a theoretically perfect staircase to show expected uniformity.
Goal: Utilize a framing square to accurately measure the riser height and tread depth at multiple points on each step, checking for consistency and any variations.
What's used
Tools
- Framing Square
About the full video
This video illustrates how to perform a visual and measurement-based inspection of older staircases to identify wear and tear that could result in building code violations related to riser height and tread depth. It emphasizes the importance of checking for consistency between steps to ensure safety and compliance, particularly for homeowners undertaking remodeling projects. While the requested context was Electrical Code Compliance, this video specifically addresses structural building codes for stairways.
Step 3 of 10: Check for Consistent Riser Height
Compare all the riser height measurements taken in Step 1. Building codes mandate that the difference in rise between any two consecutive steps should not exceed 3/8 inch. This uniformity is crucial for preventing missteps.
Every video in How to Check Your Stairs Against Building Code
Step 1: Measure Stair Rise
Step 2: Measure Stair Run
- 0:42–0:56 Measure and Verify Rise and Run
- 0:52–2:34 Measuring Rise and Run
- 2:00–2:24 Analyzing Stairway with Consistent Nosings (Correct Design)
Step 3: Check for Consistent Riser Height
- 0:31–1:01 Measure Riser Height and Tread Depth Consistency (this video)
- 4:28–6:49 Maximum Riser and Tread Difference
- 3:09–3:40 Set Riser Height and Consistency
Step 4: Check for Consistent Tread Depth (Run)
Step 5: Inspect Tread Nosing
Step 6: Check Stair Width
- 1:36–2:19 Minimum Stairway Width
- 1:34–2:22 Determine Overall Stair Width
- 0:00–0:40 Understand Minimum Stairway Width
Step 7: Inspect Handrails
- 0:24–0:42 Check Railing Height
- 4:07–4:38 Inspect Commercial Stair Handrails
- 1:50–2:05 Measure Handrail Height
Step 8: Inspect Balusters and Guardrails
- 5:28–6:08 Check Guardrail Openings
- 0:29–0:58 Measure Baluster Spacing for Code Compliance
- 0:25–0:29 Check Guardrail Opening Size
Step 9: Check Headroom
- 2:19–2:52 Minimum Headroom Height
- 0:40–1:12 Determine Minimum Headroom Height
- 10:28–12:22 Verify Fitment and Headroom in Space
Step 10: Evaluate Landing Requirements
- 12:40–15:25 Understand Landing Code Requirements
- 17:28–23:43 Identify Landing Size Requirements
- 6:03–6:46 Implement Landings
How to Check Your Stairs Against Building Code
This project outlines the process for a DIYer to check their existing stairs against common building code requirements. It involves understanding key measurements and features of stairs and comparing them to established standards. The goal is to identify any potential safety issues or code violations.
Read the full guide Browse all guides
Planning this project? Shop Oak Valley Designs.

