Check Guardrail Openings
From How to Check Your Stairs Against Building Code · Step 8 of 10 · Video by Jeremy Booth

Showing 5:28–6:08 of the source video. Watch the full video with every moment.
What happens in this clip
Inspect all open spaces within the guardrail panels to ensure safety, particularly for child protection. No open space within a guardrail panel, including areas between pickets, between the wall and the guardrail, and underneath the lowest bar of the guardrail (whether to the floor or the stair), must be large enough to allow a 4-inch (101mm) sphere to pass through. You can use a 4-inch sphere or a tape measure to check these gaps. Visually scan and systematically measure all potential openings to confirm compliance.
What's used
Tools
- 4-inch (101mm) Sphere
- Tape Measure
About the full video
This guide provides instructions for checking handrails and guardrails against International Building Code standards to ensure safety and compliance in both commercial and residential settings. It covers dimensions, spacing, and placement requirements for various railing types.
What's said in this clip
tall the two pictures on the top show the heights of the guardrails being measured the left is on a stair while the right is on a ledge each panel of a guardrail must not have a space large enough for a four inch sphere to pass through measure each open space including the spaces between pickets between the wall and the guardrail and underneath the lowest bar of a guardrail and either the floor or the stair in the bottom three pictures the space is created by the guardrail are being checked the left is showing the space between the lowest bar of the guardrail and the stairway the middle is showing the space between pickets and the right picture shows the space between the wall and the post of a car grill
Automatically transcribed from the source video.
Step 8 of 10: Inspect Balusters and Guardrails
Measure the clear space between balusters (spindles) to ensure no object larger than 4 inches can pass through. This prevents children from getting stuck. Inspect guardrails (if present) for stability and ensure they meet the required height (typically 36 inches on open sides of stairs and landings).
Every video in How to Check Your Stairs Against Building Code
Step 1: Measure Stair Rise
Step 2: Measure Stair Run
- 0:42–0:56 Measure and Verify Rise and Run
- 0:52–2:34 Measuring Rise and Run
- 2:00–2:24 Analyzing Stairway with Consistent Nosings (Correct Design)
Step 3: Check for Consistent Riser Height
- 0:31–1:01 Measure Riser Height and Tread Depth Consistency
- 4:28–6:49 Maximum Riser and Tread Difference
- 3:09–3:40 Set Riser Height and Consistency
Step 4: Check for Consistent Tread Depth (Run)
Step 5: Inspect Tread Nosing
Step 6: Check Stair Width
- 1:36–2:19 Minimum Stairway Width
- 1:34–2:22 Determine Overall Stair Width
- 0:00–0:40 Understand Minimum Stairway Width
Step 7: Inspect Handrails
- 0:24–0:42 Check Railing Height
- 4:07–4:38 Inspect Commercial Stair Handrails
- 1:50–2:05 Measure Handrail Height
Step 8: Inspect Balusters and Guardrails
- 5:28–6:08 Check Guardrail Openings (this video)
- 0:29–0:58 Measure Baluster Spacing for Code Compliance
- 0:25–0:29 Check Guardrail Opening Size
Step 9: Check Headroom
- 2:19–2:52 Minimum Headroom Height
- 0:40–1:12 Determine Minimum Headroom Height
- 10:28–12:22 Verify Fitment and Headroom in Space
Step 10: Evaluate Landing Requirements
- 12:40–15:25 Understand Landing Code Requirements
- 17:28–23:43 Identify Landing Size Requirements
- 6:03–6:46 Implement Landings
How to Check Your Stairs Against Building Code
This project outlines the process for a DIYer to check their existing stairs against common building code requirements. It involves understanding key measurements and features of stairs and comparing them to established standards. The goal is to identify any potential safety issues or code violations.
Read the full guide Browse all guides
Planning this project? Shop Oak Valley Designs.

