Analyzing Stairway Without Step Nosings (Deck Nosing Present)
From How to Check Your Stairs Against Building Code · Step 5 of 10 · Video by stairbuilding

Showing 0:37–1:59 of the source video. Watch the full video with every moment.
What happens in this clip
This step analyzes a stairway design where the individual steps lack a nosing (overhang), but the upper deck, to which the top step connects, has a 1-inch overhang. The presenter clarifies that, according to building codes, the tread measurement for the top step is taken from the farthest protruding section of the deck (including its 1-inch overhang) to the farthest projecting point of the step below. This means that despite the physical step being 11 inches deep, the code-compliant measurement becomes 10 inches for that top step. This creates an inconsistency with the other steps, which have a full 11-inch tread. The presenter notes that this specific scenario (deck having a nosing but steps not) is rare and that most building inspectors might not even catch this subtle discrepancy. He suggests a simple fix for this specific problem: remove the deck board, rip (cut) off the 1-inch overhang, and reinstall it to eliminate the nosing on the deck.
Goal: Identify and understand code measurement issues when a deck has a nosing but steps do not.
What's used
Tools
- 3D Modeling Software
About the full video
This video illustrates common construction errors in stairway design, focusing on tread depth measurements and the use of nosings. It highlights how inconsistencies can lead to code violations and potential safety hazards, offering insights into correct and incorrect approaches.
Step 5 of 10: Inspect Tread Nosing
The nosing is the projecting edge of the tread. Codes often specify that the nosing should not exceed a certain projection (typically 1 to 1.5 inches) and that the radius of the nosing should be consistent. Some codes may require that the bottom of the nosing should not extend beyond the face of the riser below it by more than 1/2 inch to prevent toe-catching.
Every video in How to Check Your Stairs Against Building Code
Step 1: Measure Stair Rise
Step 2: Measure Stair Run
- 0:42–0:56 Measure and Verify Rise and Run
- 0:52–2:34 Measuring Rise and Run
- 2:00–2:24 Analyzing Stairway with Consistent Nosings (Correct Design)
Step 3: Check for Consistent Riser Height
- 0:31–1:01 Measure Riser Height and Tread Depth Consistency
- 4:28–6:49 Maximum Riser and Tread Difference
- 3:09–3:40 Set Riser Height and Consistency
Step 4: Check for Consistent Tread Depth (Run)
Step 5: Inspect Tread Nosing
- 4:57–5:37 Specify Nosing Requirements
- 0:37–1:59 Analyzing Stairway Without Step Nosings (Deck Nosing Present) (this video)
- 2:00–2:24 Analyzing Stairway with Consistent Nosings (Correct Design)
Step 6: Check Stair Width
- 1:36–2:19 Minimum Stairway Width
- 1:34–2:22 Determine Overall Stair Width
- 0:00–0:40 Understand Minimum Stairway Width
Step 7: Inspect Handrails
- 0:24–0:42 Check Railing Height
- 4:07–4:38 Inspect Commercial Stair Handrails
- 1:50–2:05 Measure Handrail Height
Step 8: Inspect Balusters and Guardrails
- 5:28–6:08 Check Guardrail Openings
- 0:29–0:58 Measure Baluster Spacing for Code Compliance
- 0:25–0:29 Check Guardrail Opening Size
Step 9: Check Headroom
- 2:19–2:52 Minimum Headroom Height
- 0:40–1:12 Determine Minimum Headroom Height
- 10:28–12:22 Verify Fitment and Headroom in Space
Step 10: Evaluate Landing Requirements
- 12:40–15:25 Understand Landing Code Requirements
- 17:28–23:43 Identify Landing Size Requirements
- 6:03–6:46 Implement Landings
How to Check Your Stairs Against Building Code
This project outlines the process for a DIYer to check their existing stairs against common building code requirements. It involves understanding key measurements and features of stairs and comparing them to established standards. The goal is to identify any potential safety issues or code violations.
Read the full guide Browse all guides
Planning this project? Shop Oak Valley Designs.

