Install Remaining Treads and Risers
From How to Cover Waterfall-Style Stairs with Treads · Step 6 of 9 · Video by MatthiasWandel

Showing 3:28–6:52 of the source video. Watch the full video with every moment.
What happens in this clip
Continue the installation process for the remaining steps. For each step, apply construction adhesive to the existing step surface. Place the cut stair tread, ensuring a snug fit. Then, apply construction adhesive to the back of the prepared riser, and insert any necessary support wedges. Secure the riser with a nail gun. Repeat this pattern, working your way up the staircase. Pay close attention to alignment and ensure each piece is firmly set before moving to the next. The back edge of each tread will be covered by the next riser, so visible nails in that area are acceptable.
Goal: Complete the installation of all new stair treads and risers
What's used
Tools
- Caulk Gun
- Nail Gun Porter-Cable
- Brad nailer
Materials
- Bevel Cut Risers
- modified for fit.
- Construction Adhesive PL (Polyurethane)
- Gorilla Glue Construction Adhesive
- Finishing Nails
- New Stair Treads
- Scrap Wood Wedge
About the full video
This project provides a detailed guide on how to install pre-fabricated stair treads and risers onto an existing wooden staircase. The process involves precise measurement, cutting, and custom fitting of the risers to accommodate the new treads, followed by securing them with construction adhesive and a nail gun. The aim is to upgrade the appearance of a staircase by covering existing unfinished steps with new, decorative wood pieces.
Step 6 of 9: Apply Adhesive and Fasteners
Apply a generous bead of high-quality construction adhesive to the back of each new tread. Spread the adhesive evenly, ensuring good coverage, especially along the edges and towards the nosing. For waterfall treads, ensure adhesive is applied to the entire surface that will contact the existing tread. Immediately after applying adhesive, position the tread onto the existing stair. For added security, pre-drill pilot holes through the new tread into the existing tread below, and then drive screws or finish nails. Ensure fasteners are countersunk slightly below the surface for a clean finish. For waterfall edges, consider using specialized brackets or reinforcing blocks if required by the design or for structural integrity.
Every video in How to Cover Waterfall-Style Stairs with Treads
Step 1: Inspect Existing Treads and Risers
- 0:04–1:28 Assess Existing Staircase & Components
- 0:00–0:13 Assess Existing Stairs and Planning
- 1:02–1:35 Visually Inspect for Staircase Wear and Damage
Step 2: Measure and Template for New Treads
- 0:41–1:06 Measure and Mark Treads
- 0:55–1:05 Measure and Cut First Tread
- 0:18–0:49 Measure Stair Tread and Riser
Step 3: Cut New Treads
- 4:34–5:55 Measure and Cut Treads
- 0:43–0:52 Measure and Cut New Treads
- 7:06–9:20 Mark & Cut New Treads/Risers
Step 4: Prepare Existing Surfaces
- 7:20–7:47 Prepare Existing Stairs for Installation
- 1:40–2:44 Prepare Surface by Filling Holes
- 0:12–0:18 Sand & Prepare Stair Surfaces
Step 5: Dry Fit New Treads
- 19:07–19:52 Dry-Fit and Test Treads
- 1:46–2:21 Install First Tread
- 6:45–8:03 Install New Treads and Secure with Shims/Glue/Nails
Step 6: Apply Adhesive and Fasteners
- 2:32–3:28 Install First Tread and Riser
- 3:28–6:52 Install Remaining Treads and Risers (this video)
- 9:53 Install New Treads
Step 7: Install Waterfall Risers/Returns (if applicable)
- 15:24–19:11 Install Risers and Treads
- 1:04–1:15 Install Risers (Counter Stairs)
- 12:53–14:48 Addressing Exposed Staircase Ends
Step 8: Fill and Sand Fastener Holes
- 4:25–4:47 Fill Gaps and Nail Holes
- 3:59–4:48 Apply Wood Filler and Sand
- 6:57–8:12 Fill and Sand Wood Surfaces
Step 9: Apply Finish to Treads
- 1:18–1:37 Stain Stair Treads
- 0:39–0:43 Stain New Treads
- 6:17–7:17 Stain and Seal Treads
How to Cover Waterfall-Style Stairs with Treads
This project outlines the process of covering waterfall-style stairs with new treads. Waterfall stairs have treads that extend beyond the riser, creating an open side. This project focuses on installing new treads over existing ones, potentially for aesthetic updates or to repair worn surfaces.
Read the full guide Browse all guides
Planning this project? Shop Oak Valley Designs.

