Install New Treads
From How to Cover Waterfall-Style Stairs with Treads · Step 6 of 9 · Video by This Old House

Watch the full video with every moment.
What happens in this clip
Apply a generous bead of construction adhesive (such as Gorilla Glue Construction Adhesive) to the top edges of the stringers and along the front edge of the riser where the new tread will sit. The adhesive acts as both a strong bond and a lubricant, helping the tread slide into place. Carefully lower each custom-cut tread into its position, ensuring the rabbet joint on the back of the tread slides into the dado on the riser below it. Push the tread firmly against the riser and down onto the stringers. Use a hammer to gently tap the tread into its final, tight position if necessary. Finally, use a finish nail gun with 2 1/2-inch (8-penny) finish nails to secure the treads, driving nails through the top surface into the stringers. This combination of adhesive and nails ensures a strong, squeak-free installation.
Goal: Apply construction adhesive to the stringers and risers, then carefully install the new treads, ensuring they fit tightly into the dado joints, and secure them with a nail gun.
What's used
Tools
- Caulk Gun
- Finish Nail Gun
Materials
- 2 1/2-inch Finish Nails Senco
- Construction Adhesive Gorilla Glue
About the full video
This video provides detailed instructions on how to update an old, noisy, and discolored oak staircase by replacing the worn treads and resurfacing the risers. The process involves carefully disassembling the existing stairs, preparing the structural components, custom-cutting new oak treads to fit irregular spaces, and applying an oak veneer to the risers for a refreshed, modern look. The project focuses on improving aesthetics, reducing noise, and extending the lifespan of the staircase.
Step 6 of 9: Apply Adhesive and Fasteners
Apply a generous bead of high-quality construction adhesive to the back of each new tread. Spread the adhesive evenly, ensuring good coverage, especially along the edges and towards the nosing. For waterfall treads, ensure adhesive is applied to the entire surface that will contact the existing tread. Immediately after applying adhesive, position the tread onto the existing stair. For added security, pre-drill pilot holes through the new tread into the existing tread below, and then drive screws or finish nails. Ensure fasteners are countersunk slightly below the surface for a clean finish. For waterfall edges, consider using specialized brackets or reinforcing blocks if required by the design or for structural integrity.
Every video in How to Cover Waterfall-Style Stairs with Treads
Step 1: Inspect Existing Treads and Risers
- 0:04–1:28 Assess Existing Staircase & Components
- 0:00–0:13 Assess Existing Stairs and Planning
- 1:02–1:35 Visually Inspect for Staircase Wear and Damage
Step 2: Measure and Template for New Treads
- 0:41–1:06 Measure and Mark Treads
- 0:55–1:05 Measure and Cut First Tread
- 0:18–0:49 Measure Stair Tread and Riser
Step 3: Cut New Treads
- 4:34–5:55 Measure and Cut Treads
- 0:43–0:52 Measure and Cut New Treads
- 7:06–9:20 Mark & Cut New Treads/Risers
Step 4: Prepare Existing Surfaces
- 7:20–7:47 Prepare Existing Stairs for Installation
- 1:40–2:44 Prepare Surface by Filling Holes
- 0:12–0:18 Sand & Prepare Stair Surfaces
Step 5: Dry Fit New Treads
- 19:07–19:52 Dry-Fit and Test Treads
- 1:46–2:21 Install First Tread
- 6:45–8:03 Install New Treads and Secure with Shims/Glue/Nails
Step 6: Apply Adhesive and Fasteners
- 2:32–3:28 Install First Tread and Riser
- 3:28–6:52 Install Remaining Treads and Risers
- 9:53 Install New Treads (this video)
Step 7: Install Waterfall Risers/Returns (if applicable)
- 15:24–19:11 Install Risers and Treads
- 1:04–1:15 Install Risers (Counter Stairs)
- 12:53–14:48 Addressing Exposed Staircase Ends
Step 8: Fill and Sand Fastener Holes
- 4:25–4:47 Fill Gaps and Nail Holes
- 3:59–4:48 Apply Wood Filler and Sand
- 6:57–8:12 Fill and Sand Wood Surfaces
Step 9: Apply Finish to Treads
- 1:18–1:37 Stain Stair Treads
- 0:39–0:43 Stain New Treads
- 6:17–7:17 Stain and Seal Treads
How to Cover Waterfall-Style Stairs with Treads
This project outlines the process of covering waterfall-style stairs with new treads. Waterfall stairs have treads that extend beyond the riser, creating an open side. This project focuses on installing new treads over existing ones, potentially for aesthetic updates or to repair worn surfaces.
Read the full guide Browse all guides
Planning this project? Shop Oak Valley Designs.

