Stain and Seal Treads
From How to Cover Waterfall-Style Stairs with Treads · Step 9 of 9 · Video by Komar Project

Showing 6:17–7:17 of the source video. Watch the full video with every moment.
What happens in this clip
Apply painter's tape to the perimeter of the treads, along the stringers and risers, to protect them from stain and polyurethane. Apply your chosen wood stain to the oak plywood treads and bullnose using a cloth or brush. The video creator initially used 'Early American' but found it too brown, so a second coat of a 'beige' tone was applied to achieve a greyish shade that matched the existing flooring. Continue applying coats of stain until the desired color is achieved. Once the stain is dry, apply a single coat of Minwax One Coat Polyurethane to the stained treads and bullnose using a natural bristle brush. Ensure even coverage and smooth out any brush marks with light strokes.
Goal: Color and protect the new oak treads
What's used
Tools
- Gloves
- Minwax One Coat Polyurethane Minwax
- Natural Bristle Brush
- Clean rag
- Painter's Tape
- Wood Stain
- Water-based stain
About the full video
This project provides a comprehensive, step-by-step guide to renovating unfinished basement stairs to achieve a polished, modern look for under $200. It involves adding trim, spackling, sanding, priming, adding oak plywood treads with a solid oak bullnose, staining and sealing the treads, installing hardboard risers, and finally caulking and painting the stringers and risers.
Step 9 of 9: Apply Finish to Treads
If staining, apply the chosen stain evenly to the new treads, following the product's instructions. Wipe off excess stain after the recommended time. Allow the stain to dry completely. Once dry, apply multiple coats of a durable polyurethane or other suitable clear finish. Apply thin, even coats, allowing adequate drying time between each. Lightly sand with very fine-grit sandpaper (e.g., 320-400 grit) between coats for a smoother finish, and wipe away dust with a tack cloth after each sanding. Pay special attention to sealing the edges and the waterfall overhang.
Every video in How to Cover Waterfall-Style Stairs with Treads
Step 1: Inspect Existing Treads and Risers
- 0:04–1:28 Assess Existing Staircase & Components
- 0:00–0:13 Assess Existing Stairs and Planning
- 1:02–1:35 Visually Inspect for Staircase Wear and Damage
Step 2: Measure and Template for New Treads
- 0:41–1:06 Measure and Mark Treads
- 0:55–1:05 Measure and Cut First Tread
- 0:18–0:49 Measure Stair Tread and Riser
Step 3: Cut New Treads
- 4:34–5:55 Measure and Cut Treads
- 0:43–0:52 Measure and Cut New Treads
- 7:06–9:20 Mark & Cut New Treads/Risers
Step 4: Prepare Existing Surfaces
- 7:20–7:47 Prepare Existing Stairs for Installation
- 1:40–2:44 Prepare Surface by Filling Holes
- 0:12–0:18 Sand & Prepare Stair Surfaces
Step 5: Dry Fit New Treads
- 19:07–19:52 Dry-Fit and Test Treads
- 1:46–2:21 Install First Tread
- 6:45–8:03 Install New Treads and Secure with Shims/Glue/Nails
Step 6: Apply Adhesive and Fasteners
- 2:32–3:28 Install First Tread and Riser
- 3:28–6:52 Install Remaining Treads and Risers
- 9:53 Install New Treads
Step 7: Install Waterfall Risers/Returns (if applicable)
- 15:24–19:11 Install Risers and Treads
- 1:04–1:15 Install Risers (Counter Stairs)
- 12:53–14:48 Addressing Exposed Staircase Ends
Step 8: Fill and Sand Fastener Holes
- 4:25–4:47 Fill Gaps and Nail Holes
- 3:59–4:48 Apply Wood Filler and Sand
- 6:57–8:12 Fill and Sand Wood Surfaces
Step 9: Apply Finish to Treads
- 1:18–1:37 Stain Stair Treads
- 0:39–0:43 Stain New Treads
- 6:17–7:17 Stain and Seal Treads (this video)
How to Cover Waterfall-Style Stairs with Treads
This project outlines the process of covering waterfall-style stairs with new treads. Waterfall stairs have treads that extend beyond the riser, creating an open side. This project focuses on installing new treads over existing ones, potentially for aesthetic updates or to repair worn surfaces.
Read the full guide Browse all guides
Planning this project? Shop Oak Valley Designs.

