Install Risers (Counter Stairs)
From How to Cover Waterfall-Style Stairs with Treads · Step 7 of 9 · Video by soyourerenovating

Showing 1:04–1:15 of the source video. Watch the full video with every moment.
What happens in this clip
After installing all the treads, proceed to measure, cut, and glue each counter stair (riser). Measure the height and width of the space between each newly installed tread. Cut the new wooden risers to fit these dimensions precisely. Apply construction wood adhesive to the back of each riser and firmly press it into place, ensuring a tight fit between the treads.
Goal: Cover the vertical spaces between stair treads with new risers.
What's used
Tools
- Caulking Gun
- Pencil
- Saw (e.g.
- Miter Saw
- Table Saw
- Jigsaw)
- Tape Measure
Materials
- Construction Wood Adhesive PL 400
- Polyurethane construction adhesive
- New Wooden Risers
About the full video
This DIY project guides you through completely renovating old carpeted stairs by removing the old carpet, cutting off existing bullnoses, securing loose stairs, installing new hardwood treads and risers, and finally staining them for a polished look.
Step 7 of 9: Install Waterfall Risers/Returns (if applicable)
For waterfall stairs, you may have a separate piece that covers the exposed edge of the tread where it extends beyond the riser. This is often called a return. Measure and cut these return pieces to precisely fit the dimensions of the tread's overhang and the adjacent riser. Apply construction adhesive to the back of the return piece and secure it to the tread and any adjoining surfaces. You may also need to fasten these with brad nails or a routered dado for a stronger connection. Ensure the joints are tight and flush.
Every video in How to Cover Waterfall-Style Stairs with Treads
Step 1: Inspect Existing Treads and Risers
- 0:04–1:28 Assess Existing Staircase & Components
- 0:00–0:13 Assess Existing Stairs and Planning
- 1:02–1:35 Visually Inspect for Staircase Wear and Damage
Step 2: Measure and Template for New Treads
- 0:41–1:06 Measure and Mark Treads
- 0:55–1:05 Measure and Cut First Tread
- 0:18–0:49 Measure Stair Tread and Riser
Step 3: Cut New Treads
- 4:34–5:55 Measure and Cut Treads
- 0:43–0:52 Measure and Cut New Treads
- 7:06–9:20 Mark & Cut New Treads/Risers
Step 4: Prepare Existing Surfaces
- 7:20–7:47 Prepare Existing Stairs for Installation
- 1:40–2:44 Prepare Surface by Filling Holes
- 0:12–0:18 Sand & Prepare Stair Surfaces
Step 5: Dry Fit New Treads
- 19:07–19:52 Dry-Fit and Test Treads
- 1:46–2:21 Install First Tread
- 6:45–8:03 Install New Treads and Secure with Shims/Glue/Nails
Step 6: Apply Adhesive and Fasteners
- 2:32–3:28 Install First Tread and Riser
- 3:28–6:52 Install Remaining Treads and Risers
- 9:53 Install New Treads
Step 7: Install Waterfall Risers/Returns (if applicable)
- 15:24–19:11 Install Risers and Treads
- 1:04–1:15 Install Risers (Counter Stairs) (this video)
- 12:53–14:48 Addressing Exposed Staircase Ends
Step 8: Fill and Sand Fastener Holes
- 4:25–4:47 Fill Gaps and Nail Holes
- 3:59–4:48 Apply Wood Filler and Sand
- 6:57–8:12 Fill and Sand Wood Surfaces
Step 9: Apply Finish to Treads
- 1:18–1:37 Stain Stair Treads
- 0:39–0:43 Stain New Treads
- 6:17–7:17 Stain and Seal Treads
How to Cover Waterfall-Style Stairs with Treads
This project outlines the process of covering waterfall-style stairs with new treads. Waterfall stairs have treads that extend beyond the riser, creating an open side. This project focuses on installing new treads over existing ones, potentially for aesthetic updates or to repair worn surfaces.
Read the full guide Browse all guides
Planning this project? Shop Oak Valley Designs.

