Dry-Fit and Test Treads
From How to Cover Waterfall-Style Stairs with Treads · Step 5 of 9 · Video by Insider Carpentry - Spencer Lewis

Showing 19:07–19:52 of the source video. Watch the full video with every moment.
What happens in this clip
Before permanently installing the treads, dry-fit them into place. Gently slide each tread under the previously installed riser. Check that the tread fits snugly against the skirt board on both sides and that it is tight against the riser. A good fit means minimal gaps on the sides and a flush connection with the riser. If a tread is too tight, it may need slight sanding or trimming. If it's too loose, you might need to adjust or recut. After confirming a good dry fit, carefully remove the treads, ensuring not to damage the risers.
Goal: Verify the precise fit of each cut tread before permanent installation.
What's used
Materials
- Cut Tread
About the full video
This video provides a detailed guide on installing wooden stair risers and treads using a unique interlocking joint technique. It covers the preparation of materials, precise measurement and cutting methods for both risers and treads, and their final installation, emphasizing accuracy and the use of specialized tools for a seamless and sturdy finish.
Step 5 of 9: Dry Fit New Treads
Carefully place each new tread onto its corresponding existing tread. Check for a snug fit against the risers and any adjacent vertical surfaces. Ensure the waterfall overhang is correctly positioned and that the tread sits level. Make any minor adjustments by carefully trimming or sanding edges as needed to achieve a perfect fit. This step is critical to avoid costly mistakes during the adhesive and fastening stage.
Every video in How to Cover Waterfall-Style Stairs with Treads
Step 1: Inspect Existing Treads and Risers
- 0:04–1:28 Assess Existing Staircase & Components
- 0:00–0:13 Assess Existing Stairs and Planning
- 1:02–1:35 Visually Inspect for Staircase Wear and Damage
Step 2: Measure and Template for New Treads
- 0:41–1:06 Measure and Mark Treads
- 0:55–1:05 Measure and Cut First Tread
- 0:18–0:49 Measure Stair Tread and Riser
Step 3: Cut New Treads
- 4:34–5:55 Measure and Cut Treads
- 0:43–0:52 Measure and Cut New Treads
- 7:06–9:20 Mark & Cut New Treads/Risers
Step 4: Prepare Existing Surfaces
- 7:20–7:47 Prepare Existing Stairs for Installation
- 1:40–2:44 Prepare Surface by Filling Holes
- 0:12–0:18 Sand & Prepare Stair Surfaces
Step 5: Dry Fit New Treads
- 19:07–19:52 Dry-Fit and Test Treads (this video)
- 1:46–2:21 Install First Tread
- 6:45–8:03 Install New Treads and Secure with Shims/Glue/Nails
Step 6: Apply Adhesive and Fasteners
- 2:32–3:28 Install First Tread and Riser
- 3:28–6:52 Install Remaining Treads and Risers
- 9:53 Install New Treads
Step 7: Install Waterfall Risers/Returns (if applicable)
- 15:24–19:11 Install Risers and Treads
- 1:04–1:15 Install Risers (Counter Stairs)
- 12:53–14:48 Addressing Exposed Staircase Ends
Step 8: Fill and Sand Fastener Holes
- 4:25–4:47 Fill Gaps and Nail Holes
- 3:59–4:48 Apply Wood Filler and Sand
- 6:57–8:12 Fill and Sand Wood Surfaces
Step 9: Apply Finish to Treads
- 1:18–1:37 Stain Stair Treads
- 0:39–0:43 Stain New Treads
- 6:17–7:17 Stain and Seal Treads
How to Cover Waterfall-Style Stairs with Treads
This project outlines the process of covering waterfall-style stairs with new treads. Waterfall stairs have treads that extend beyond the riser, creating an open side. This project focuses on installing new treads over existing ones, potentially for aesthetic updates or to repair worn surfaces.
Read the full guide Browse all guides
Planning this project? Shop Oak Valley Designs.

