Visually Inspect for Staircase Wear and Damage
From How to Cover Waterfall-Style Stairs with Treads · Step 1 of 9 · Video by stairbuilding

Showing 1:02–1:35 of the source video. Watch the full video with every moment.
What happens in this clip
After understanding the measurement technique, the video shifts to visually examining the staircase for any obvious signs of wear and tear, which are more common in older structures. It points out that the center sections of the treads are most susceptible to abuse from repeated foot traffic over time. Look for chipped or missing nosing (the front edge of the tread), split sections of the wood, or noticeable depressions and unevenness on the tread surfaces. These visual cues often indicate areas where code violations due to excessive variation are most likely to occur.
Goal: Conduct a visual assessment of the staircase to identify obvious signs of wear, such as missing nosing, split sections, or depressions in the treads, which are common in high-traffic areas.
About the full video
This video illustrates how to perform a visual and measurement-based inspection of older staircases to identify wear and tear that could result in building code violations related to riser height and tread depth. It emphasizes the importance of checking for consistency between steps to ensure safety and compliance, particularly for homeowners undertaking remodeling projects. While the requested context was Electrical Code Compliance, this video specifically addresses structural building codes for stairways.
Step 1 of 9: Inspect Existing Treads and Risers
Carefully examine each existing stair tread and riser. Look for any signs of damage such as cracks, splits, or deep gouges. Check if any treads or risers are loose, squeaky, or wobbly. Identify any areas of rot, water damage, or delamination, particularly on the edges and undersides. Note any areas that appear uneven or out of level, as these will need to be addressed before new treads are installed.
Every video in How to Cover Waterfall-Style Stairs with Treads
Step 1: Inspect Existing Treads and Risers
- 0:04–1:28 Assess Existing Staircase & Components
- 0:00–0:13 Assess Existing Stairs and Planning
- 1:02–1:35 Visually Inspect for Staircase Wear and Damage (this video)
Step 2: Measure and Template for New Treads
- 0:41–1:06 Measure and Mark Treads
- 0:55–1:05 Measure and Cut First Tread
- 0:18–0:49 Measure Stair Tread and Riser
Step 3: Cut New Treads
- 4:34–5:55 Measure and Cut Treads
- 0:43–0:52 Measure and Cut New Treads
- 7:06–9:20 Mark & Cut New Treads/Risers
Step 4: Prepare Existing Surfaces
- 7:20–7:47 Prepare Existing Stairs for Installation
- 1:40–2:44 Prepare Surface by Filling Holes
- 0:12–0:18 Sand & Prepare Stair Surfaces
Step 5: Dry Fit New Treads
- 19:07–19:52 Dry-Fit and Test Treads
- 1:46–2:21 Install First Tread
- 6:45–8:03 Install New Treads and Secure with Shims/Glue/Nails
Step 6: Apply Adhesive and Fasteners
- 2:32–3:28 Install First Tread and Riser
- 3:28–6:52 Install Remaining Treads and Risers
- 9:53 Install New Treads
Step 7: Install Waterfall Risers/Returns (if applicable)
- 15:24–19:11 Install Risers and Treads
- 1:04–1:15 Install Risers (Counter Stairs)
- 12:53–14:48 Addressing Exposed Staircase Ends
Step 8: Fill and Sand Fastener Holes
- 4:25–4:47 Fill Gaps and Nail Holes
- 3:59–4:48 Apply Wood Filler and Sand
- 6:57–8:12 Fill and Sand Wood Surfaces
Step 9: Apply Finish to Treads
- 1:18–1:37 Stain Stair Treads
- 0:39–0:43 Stain New Treads
- 6:17–7:17 Stain and Seal Treads
How to Cover Waterfall-Style Stairs with Treads
This project outlines the process of covering waterfall-style stairs with new treads. Waterfall stairs have treads that extend beyond the riser, creating an open side. This project focuses on installing new treads over existing ones, potentially for aesthetic updates or to repair worn surfaces.
Read the full guide Browse all guides
Planning this project? Shop Oak Valley Designs.

