Mark & Cut New Treads/Risers
From How to Cover Waterfall-Style Stairs with Treads · Step 3 of 9 · Video by This Old House

Showing 7:06–9:20 of the source video. Watch the full video with every moment.
What happens in this clip
Carefully place the cardboard template onto the new red oak lumber (1x12 red oak is suggested, 3/4 inch thick and 11.5 inches wide, available at home centers). Ensure the template is positioned so that the cut marks will result in a tread of the correct length and the nosing (rounded edge) remains intact. Secure the template to prevent movement while tracing. Once transferred, use a small circular saw to make the initial cuts along the marked lines. Then, use a router with the appropriate bit to create the rabbet joint on the back edge of the tread. This rabbet cut will form the tongue that fits into the dado (groove) on the existing stringer, allowing the tread to sit flush and securely. For accuracy, make sure the template marks are visible, and cut just outside the line to allow for fine-tuning if necessary. Remember that the cuts are not always square or parallel, so precise marking is essential.
Goal: Transfer the custom template marks to new red oak lumber, then precisely cut each new tread and router the rabbet joint to fit perfectly into the existing dado in the stringers.
What's used
Tools
- New Red Oak Lumber (1x12)
- Pencil
- Router
- Small Circular Saw
- Band saw
About the full video
This video provides detailed instructions on how to update an old, noisy, and discolored oak staircase by replacing the worn treads and resurfacing the risers. The process involves carefully disassembling the existing stairs, preparing the structural components, custom-cutting new oak treads to fit irregular spaces, and applying an oak veneer to the risers for a refreshed, modern look. The project focuses on improving aesthetics, reducing noise, and extending the lifespan of the staircase.
Step 3 of 9: Cut New Treads
Transfer the dimensions or template outlines onto your new tread material (e.g., hardwood, engineered wood). Using a circular saw or jigsaw, carefully cut out each tread. Ensure all cuts are straight and accurate, especially for the edges that will meet risers or other treads, and the waterfall overhang. If cutting hardwood, consider using a fine-tooth blade to minimize tear-out and achieve a cleaner edge.
Every video in How to Cover Waterfall-Style Stairs with Treads
Step 1: Inspect Existing Treads and Risers
- 0:04–1:28 Assess Existing Staircase & Components
- 0:00–0:13 Assess Existing Stairs and Planning
- 1:02–1:35 Visually Inspect for Staircase Wear and Damage
Step 2: Measure and Template for New Treads
- 0:41–1:06 Measure and Mark Treads
- 0:55–1:05 Measure and Cut First Tread
- 0:18–0:49 Measure Stair Tread and Riser
Step 3: Cut New Treads
- 4:34–5:55 Measure and Cut Treads
- 0:43–0:52 Measure and Cut New Treads
- 7:06–9:20 Mark & Cut New Treads/Risers (this video)
Step 4: Prepare Existing Surfaces
- 7:20–7:47 Prepare Existing Stairs for Installation
- 1:40–2:44 Prepare Surface by Filling Holes
- 0:12–0:18 Sand & Prepare Stair Surfaces
Step 5: Dry Fit New Treads
- 19:07–19:52 Dry-Fit and Test Treads
- 1:46–2:21 Install First Tread
- 6:45–8:03 Install New Treads and Secure with Shims/Glue/Nails
Step 6: Apply Adhesive and Fasteners
- 2:32–3:28 Install First Tread and Riser
- 3:28–6:52 Install Remaining Treads and Risers
- 9:53 Install New Treads
Step 7: Install Waterfall Risers/Returns (if applicable)
- 15:24–19:11 Install Risers and Treads
- 1:04–1:15 Install Risers (Counter Stairs)
- 12:53–14:48 Addressing Exposed Staircase Ends
Step 8: Fill and Sand Fastener Holes
- 4:25–4:47 Fill Gaps and Nail Holes
- 3:59–4:48 Apply Wood Filler and Sand
- 6:57–8:12 Fill and Sand Wood Surfaces
Step 9: Apply Finish to Treads
- 1:18–1:37 Stain Stair Treads
- 0:39–0:43 Stain New Treads
- 6:17–7:17 Stain and Seal Treads
How to Cover Waterfall-Style Stairs with Treads
This project outlines the process of covering waterfall-style stairs with new treads. Waterfall stairs have treads that extend beyond the riser, creating an open side. This project focuses on installing new treads over existing ones, potentially for aesthetic updates or to repair worn surfaces.
Read the full guide Browse all guides
Planning this project? Shop Oak Valley Designs.

