Disconnect the Wires Connected to the Outlet Switch
From How to Install a Motion-Sensor Light Switch in a Stairway · Step 3 of 8 · Video by ForRent.com

Showing 0:47–1:01 of the source video. Watch the full video with every moment.
What happens in this clip
Before disconnecting any wires, take a photo or make a clear diagram of how the wires are connected to the existing light switch. This is crucial for correctly wiring the new switch. Typically, a single-pole switch will have two hot wires (usually black) connected to the side terminals and a bare copper or green ground wire connected to the green ground screw. Use your flathead screwdriver to loosen the terminal screws and carefully unwrap each wire from its connection point on the old switch. If necessary, use wire strippers to clean up the ends of the wires.
Goal: Remove the old switch by detaching its electrical connections
What's used
Tools
- Flathead Screwdriver
- Light Switch (Old) Leviton
- Wire Strippers
Materials
- Electrical Tape
- Marker
About the full video
This project provides a step-by-step guide on how to safely replace a broken light switch in your home. It emphasizes essential safety precautions, such as cutting power at the circuit breaker and using a voltage tester, before detailing the process of removing the old switch, disconnecting wires, installing a new switch, and restoring power.
Step 3 of 8: Identify and Disconnect Wires
Examine the wires connected to the old switch. Typically, you will find a 'line' wire (power coming in), a 'load' wire (power going to the light), and a 'ground' wire (bare copper or green). Loosen the terminal screws or release the wires from the push-in connectors on the old switch. Ensure the wires are not touching each other or the metal electrical box.
Every video in How to Install a Motion-Sensor Light Switch in a Stairway
Step 1: Turn Off Power
- 0:37–0:52 Cut Power at Circuit Breaker
- 0:51–0:57 Turn off Power at Breaker
- 0:49–0:55 Disconnect Power
Step 2: Remove Existing Switch Plate and Switch
- 27:53–28:00 Remove Existing Switch Plate and Switch
- 0:25–0:34 Remove Existing Light Switch
- 1:46–2:24 Remove Existing Switch and Cover
Step 3: Identify and Disconnect Wires
- 0:05–0:24 Identify and Disconnect Wires
- 2:44–4:10 Disconnect Old Switch & Identify Wires
- 0:47–1:01 Disconnect the Wires Connected to the Outlet Switch (this video)
Step 4: Connect Motion Sensor Switch - Line and Load
- 0:34–0:47 Wire the New Motion Sensor Switch
- 5:45–6:30 Wire the Motion Sensor Switch
- 0:05–0:11 Wire New Motion Sensor Switch
Step 5: Connect Ground Wire
- 3:28–3:58 Connect Ground Wires
- 0:52–0:58 Connect the Ground Wire
- 0:59–1:07 Connect Ground Wire to New Switch
Step 6: Mount the Motion Sensor Switch
- 0:11–0:12 Mount Motion Sensor Switch
- 0:47–0:55 Mount Switch and Attach Faceplate
- 2:41–3:07 Mount Switch and Adjust Settings
Step 7: Install the Cover Plate
- 7:43–7:51 Install Wall Plate
- 3:07–3:55 Install Cover Plate and Final Test
- 4:51–5:25 Mount Switch and Install Faceplate
Step 8: Restore Power and Test
- 2:14–2:58 Restore Power and Test Functionality
- 3:16–4:29 Restore Power and Test Functionality
- 5:30–5:53 Test Switch Operation
How to Install a Motion-Sensor Light Switch in a Stairway
This project outlines the steps for installing a motion sensor light switch to automate lighting in a stairway. It covers preparation, wiring, mounting, and testing the new switch.
Read the full guide Browse all guides
Planning this project? Shop Oak Valley Designs.

