Identify and Disconnect Wires
From How to Install a Motion-Sensor Light Switch in a Stairway · Step 3 of 8 · Video by Joshua Johnson

Showing 0:05–0:24 of the source video. Watch the full video with every moment.
What happens in this clip
With the old switch pulled out, use a non-contact voltage tester to confirm that the wires are completely dead and there is no live current. The video demonstrates confirming the wires are dead. Identify the ground wire (typically bare copper or green), the power wire (often black, bringing electricity from the source), and the lead wire (often black or red, taking power to the lights). On the existing switch, the top terminal typically sends power, and the bottom terminal receives it, which helps identify the load and line wires if not explicitly colored. Loosen the terminal screws on the old switch using a screwdriver and carefully disconnect all wires: the ground wire, the power wire, and the lead wire to the lights.
Goal: Safely identify and disconnect wires from the old switch
What's used
Tools
- Non-contact Voltage Tester CAT IV
- Screwdriver
About the full video
This project provides step-by-step instructions on how to replace a standard light switch with a new Lutron dimmer switch. The process covers safely removing the old switch, identifying electrical wires, connecting the new dimmer using Wago connectors, installing it into the electrical box, and finally, testing its functionality.
Step 3 of 8: Identify and Disconnect Wires
Examine the wires connected to the old switch. Typically, you will find a 'line' wire (power coming in), a 'load' wire (power going to the light), and a 'ground' wire (bare copper or green). Loosen the terminal screws or release the wires from the push-in connectors on the old switch. Ensure the wires are not touching each other or the metal electrical box.
Every video in How to Install a Motion-Sensor Light Switch in a Stairway
Step 1: Turn Off Power
- 0:37–0:52 Cut Power at Circuit Breaker
- 0:51–0:57 Turn off Power at Breaker
- 0:49–0:55 Disconnect Power
Step 2: Remove Existing Switch Plate and Switch
- 27:53–28:00 Remove Existing Switch Plate and Switch
- 0:25–0:34 Remove Existing Light Switch
- 1:46–2:24 Remove Existing Switch and Cover
Step 3: Identify and Disconnect Wires
- 0:05–0:24 Identify and Disconnect Wires (this video)
- 2:44–4:10 Disconnect Old Switch & Identify Wires
- 0:47–1:01 Disconnect the Wires Connected to the Outlet Switch
Step 4: Connect Motion Sensor Switch - Line and Load
- 0:34–0:47 Wire the New Motion Sensor Switch
- 5:45–6:30 Wire the Motion Sensor Switch
- 0:05–0:11 Wire New Motion Sensor Switch
Step 5: Connect Ground Wire
- 3:28–3:58 Connect Ground Wires
- 0:52–0:58 Connect the Ground Wire
- 0:59–1:07 Connect Ground Wire to New Switch
Step 6: Mount the Motion Sensor Switch
- 0:11–0:12 Mount Motion Sensor Switch
- 0:47–0:55 Mount Switch and Attach Faceplate
- 2:41–3:07 Mount Switch and Adjust Settings
Step 7: Install the Cover Plate
- 7:43–7:51 Install Wall Plate
- 3:07–3:55 Install Cover Plate and Final Test
- 4:51–5:25 Mount Switch and Install Faceplate
Step 8: Restore Power and Test
- 2:14–2:58 Restore Power and Test Functionality
- 3:16–4:29 Restore Power and Test Functionality
- 5:30–5:53 Test Switch Operation
How to Install a Motion-Sensor Light Switch in a Stairway
This project outlines the steps for installing a motion sensor light switch to automate lighting in a stairway. It covers preparation, wiring, mounting, and testing the new switch.
Read the full guide Browse all guides
Planning this project? Shop Oak Valley Designs.

