Disconnect Old Switch & Identify Wires
From How to Install a Motion-Sensor Light Switch in a Stairway · Step 3 of 8 · Video by Top Homeowner

Showing 2:44–4:10 of the source video. Watch the full video with every moment.
What happens in this clip
The old switch was installed using a 'back-stab' wiring method. To remove these wires, you can either push a flat-blade screwdriver into the release slot next to each wire to disengage them, or for quicker removal, you can cut the wires close to the old switch. If you cut them, you will need to re-strip them later. After the old switch is disconnected, identify the various wires in the electrical box: the neutral wires (typically white or grey, often bundled together), the ground wires (bare copper or green), and the 'line' and 'load' black wires. The 'line' wire brings power from the electrical panel, and the 'load' wire carries power to the light fixture.
Goal: Remove old switch and categorize electrical wires
What's used
Tools
- Pliers
- Screwdriver (flat-blade)
About the full video
This project provides step-by-step instructions on how to install a TP-Link Kasa Smart Wi-Fi Light Switch Dimmer (Model HS220). The installation involves safely removing an existing light switch, identifying electrical wires (line, load, neutral, and ground), connecting the new smart switch, and setting it up using the Kasa mobile application for remote control, scheduling, and dimming functionalities. It emphasizes safety precautions like turning off power at the breaker and checking for a neutral wire.
Step 3 of 8: Identify and Disconnect Wires
Examine the wires connected to the old switch. Typically, you will find a 'line' wire (power coming in), a 'load' wire (power going to the light), and a 'ground' wire (bare copper or green). Loosen the terminal screws or release the wires from the push-in connectors on the old switch. Ensure the wires are not touching each other or the metal electrical box.
Every video in How to Install a Motion-Sensor Light Switch in a Stairway
Step 1: Turn Off Power
- 0:37–0:52 Cut Power at Circuit Breaker
- 0:51–0:57 Turn off Power at Breaker
- 0:49–0:55 Disconnect Power
Step 2: Remove Existing Switch Plate and Switch
- 27:53–28:00 Remove Existing Switch Plate and Switch
- 0:25–0:34 Remove Existing Light Switch
- 1:46–2:24 Remove Existing Switch and Cover
Step 3: Identify and Disconnect Wires
- 0:05–0:24 Identify and Disconnect Wires
- 2:44–4:10 Disconnect Old Switch & Identify Wires (this video)
- 0:47–1:01 Disconnect the Wires Connected to the Outlet Switch
Step 4: Connect Motion Sensor Switch - Line and Load
- 0:34–0:47 Wire the New Motion Sensor Switch
- 5:45–6:30 Wire the Motion Sensor Switch
- 0:05–0:11 Wire New Motion Sensor Switch
Step 5: Connect Ground Wire
- 3:28–3:58 Connect Ground Wires
- 0:52–0:58 Connect the Ground Wire
- 0:59–1:07 Connect Ground Wire to New Switch
Step 6: Mount the Motion Sensor Switch
- 0:11–0:12 Mount Motion Sensor Switch
- 0:47–0:55 Mount Switch and Attach Faceplate
- 2:41–3:07 Mount Switch and Adjust Settings
Step 7: Install the Cover Plate
- 7:43–7:51 Install Wall Plate
- 3:07–3:55 Install Cover Plate and Final Test
- 4:51–5:25 Mount Switch and Install Faceplate
Step 8: Restore Power and Test
- 2:14–2:58 Restore Power and Test Functionality
- 3:16–4:29 Restore Power and Test Functionality
- 5:30–5:53 Test Switch Operation
How to Install a Motion-Sensor Light Switch in a Stairway
This project outlines the steps for installing a motion sensor light switch to automate lighting in a stairway. It covers preparation, wiring, mounting, and testing the new switch.
Read the full guide Browse all guides
Planning this project? Shop Oak Valley Designs.

