Wire the Primary Three-Way Switch
From How to Wire a 3-way Switch for Stair Lights at the Top and Bottom · Step 4 of 7 · Video by The Home Improvement Channel

Showing 5:22–7:16 of the source video. Watch the full video with every moment.
What happens in this clip
At the original switch location, you will have the incoming power cable (likely 12/2 or 14/2), the cable running to the light fixture (also 12/2 or 14/2), and the newly run 12-3 (or 14-3) cable to the secondary switch. First, identify the incoming 'hot' wire from the power source (usually black) and connect it to the common (black) screw terminal of your new primary three-way switch. Next, take the hot wire that runs to the light fixture (often black) and connect it to the white wire from the 12-3 cable that goes to the secondary switch. Remember to mark the white wire from the 12-3 with black tape on both ends to denote it's now a 'hot' conductor (common to the secondary switch). Finally, connect the red and black wires from the 12-3 cable to the two traveler (brass) screw terminals on the primary three-way switch. All bare copper ground wires from all cables in the box should be twisted together with a pigtail to the green ground screw on the switch, and all white neutral wires should be twisted together and capped with a wire nut. (Note: The video does not show neutrals being tied to the switch itself, only to each other, as is typical for dead-end three-way switches where the switch does not require a neutral connection.)
Goal: Connect all cables and wires to the primary three-way switch
What's used
Tools
- Screwdriver (Phillips or flathead)
- Three-way switch
- Wire strippers Southwire
Materials
- Black electrical tape
- Wire nuts
About the full video
This project guides you through converting an existing single-pole light switch setup into a dead-end three-way switch configuration. This allows control of a single light fixture from two different locations, which is ideal for larger rooms or hallways. The process involves running new wiring to a secondary switch location, preparing and connecting both three-way switches, and adhering to electrical code requirements regarding wire gauge and neutral conductors.
What's said in this clip
now all we got to do is hook it all up all right so here we are in our original switch location I've left the wires there for the light coming in right here you had that already and the power coming in we had that already is the only thing we've added is the 12 3 or the 14 3 which may be in your case now I've left the grounds tied together and I've left the common coming in to the common light all right here's the one that goes to the light that's the B plus coming in those two are still tied together what we need to do here's this one this is our 12 3 as these three wires right here okay we need to take the white wire which I put on the common screw on the other three-way switch right here if you've noticed I've added some black tape to that to indicate that that's hot in case somebody down the road gets the idea oh here's a white wire it must not be hot and they touch it and get zapped so we're going to tie our white wire our common wire to our light this is our light hot wire all right tie these two together and we'll go ahead and add a wire nut all right now normally you would stuff all these inside the box but I'm just going to leave them out so you can see them now these two are our Travelers right on the other switch we've got those hooked to The Travelers we're going to hook those to The Travelers on the new Switch hook the ground back up and here's our power coming from the fuse panel from the wall and that goes straight to the black screw or the common screw on our three-way switch
Automatically transcribed from the source video.
Step 4 of 7: Install new 3-way switches
At the first switch location, connect the incoming hot (LINE) wire to the 'common' terminal (usually black or a different color screw). Connect the two 'traveler' wires to the two 'traveler' terminals (usually brass screws). At the second switch location, connect the wire coming from the first switch's traveler terminals to the traveler terminals on this switch. Connect the wire going to the light fixture (LOAD) to the 'common' terminal of this switch.
Every video in How to Wire a 3-way Switch for Stair Lights at the Top and Bottom
Step 1: De-energize the circuit
- 0:08–0:36 Turn Off Circuit Breaker
- 0:03–0:08 Turn Off Power at Breaker Panel
- 2:06–2:13 Turn Off Power at Breaker
Step 2: Remove existing switch and light fixture
- 0:16–0:24 Remove Old Light Switch
- 17:23–17:28 Remove the old light switch
- 0:08–0:12 Remove Existing Light Switch
Step 3: Identify and label wires
- 2:06–2:27 Label All Wires
- 4:12–5:29 Identify the Line (Hot) Wire
- 0:25–1:15 Identify Wires and Switch Terminals
Step 4: Install new 3-way switches
- 5:49–6:58 Wire a Three-Way Switch Circuit
- 17:43–19:32 Connect Wires to Second Switch (Method 2)
- 5:22–7:16 Wire the Primary Three-Way Switch (this video)
Step 5: Wire the light fixture
- 4:17–4:29 Connect Load Wire to Common (Second Switch Box)
- 2:47–2:56 Connect Common (Light) to Switch 2
- 0:04–0:08 Connect Second Switch to Light Fixture
Step 6: Install switch and fixture covers
- 3:20–3:58 Secure New Switch and Install Button Cover
- 7:25–8:09 Install New Fixture Cover
- 1:42–1:43 Install Light Switch Cover Plate
Step 7: Restore power and test operation
- 3:39–3:54 Restore Power and Test Functionality
- 7:09–8:19 Restore Power and Test
- 6:26–6:54 Restore Power and Test Switches
Questions about How to Wire a 3-way Switch for Stair Lights at the Top and Bottom
How can I ensure I correctly identify and label the wires for a 3-way switch, especially for a beginner?
The most crucial step is identifying the 'common' wire, which is usually darker (black) and connected to a distinctively colored screw (often black or brass). The other two wires are 'travelers.' Use electrical tape or a marker to clearly label each wire immediately after identification, making sure not to confuse them between the two switch boxes.
What are the common reasons why a newly wired 3-way switch might not work, and how do I troubleshoot?
The most frequent issue is incorrectly wiring the common or traveler wires. If the light only works from one switch, or not at all, double-check that the common wire is correctly connected to the common terminal on both switches. Use your non-contact voltage tester to confirm power is reaching the switches and the fixture, and check all wire nuts for secure connections.
Is wiring a 3-way switch really a beginner-friendly project, and what's the realistic time commitment?
While labeled 'beginner,' it's more complex than a single-pole switch, requiring careful attention to wiring diagrams and wire identification. It's manageable for a patient beginner. The estimated 4 hours is a good realistic timeframe, especially for someone new to 3-way wiring, allowing for careful work and troubleshooting.
What are some alternative options or upgrades I could consider beyond a basic 3-way switch for stair lighting?
You could upgrade to dimmer-compatible 3-way switches to control light intensity, or consider smart 3-way switches for app or voice control. However, smart switches often require a neutral wire in the switch box, which might necessitate additional wiring work if your home is older and lacks one.
Do I need a permit or inspection for installing a 3-way switch system?
Local regulations vary, but any electrical work, even replacing switches, may require a permit and subsequent inspection in your area. Always check with your local building department or code enforcement office before starting the project to ensure compliance and avoid potential issues with home insurance or resale.
How to Wire a 3-way Switch for Stair Lights at the Top and Bottom
Outline for installing a 3-way switch system to control stair lights from both the top and bottom of the stairs.
Read the full guide Browse all guides
Planning this project? Shop Oak Valley Designs.

