Label All Wires
From How to Wire a 3-way Switch for Stair Lights at the Top and Bottom · Step 3 of 7 · Video by TP-Link Systems Inc.

Showing 2:06–2:27 of the source video. Watch the full video with every moment.
What happens in this clip
Using the provided wire labels, carefully label each wire in both the main switch box (where the Line wire was found) and the satellite switch box. Label the energized wire as 'Line'. Label any white wires as 'Neutral'. Label any bare copper or green insulated wires as 'Ground'. The remaining wires are your 'Traveler' wires. There should be two traveler wires. Label one 'Traveler 1' and the other 'Traveler 2'. Ensure that the corresponding traveler wires (e.g., the red wire labeled 'Traveler 1' in the main box) are labeled the same in the satellite box. Identify the 'Load' wire in the satellite box, which typically connects to the light fixture itself. This might be the remaining traveler-like wire that is not connected to the main switch's Traveler 1 or Traveler 2.
Goal: Correctly identify and label all electrical wires in both switch boxes.
What's used
Tools
- Wire Labels TP-Link Kasa (provided)
About the full video
This DIY project provides a comprehensive guide for installing and setting up the TP-Link Kasa KS230 3-way smart dimmer kit. It covers critical safety precautions, identifying and labeling existing wiring for both main and satellite switches, securely connecting the new smart dimmers, and finally configuring them using the Kasa mobile application, including dimming range calibration.
Step 3 of 7: Identify and label wires
At the first switch location (e.g., top of stairs), identify the incoming hot wire (usually black), the wire going to the light (switched hot), and the traveler wires. At the second switch location (e.g., bottom of stairs), identify the wire coming from the first switch (traveler) and the wire going to the light (switched hot). At the light fixture, identify the hot wire from the switch, the neutral wire, and the ground wire. Use electrical tape or wire nuts to label each wire clearly (e.g., 'LINE', 'LOAD', 'TRAVELER 1', 'TRAVELER 2').
Every video in How to Wire a 3-way Switch for Stair Lights at the Top and Bottom
Step 1: De-energize the circuit
- 0:08–0:36 Turn Off Circuit Breaker
- 0:03–0:08 Turn Off Power at Breaker Panel
- 2:06–2:13 Turn Off Power at Breaker
Step 2: Remove existing switch and light fixture
- 0:16–0:24 Remove Old Light Switch
- 17:23–17:28 Remove the old light switch
- 0:08–0:12 Remove Existing Light Switch
Step 3: Identify and label wires
- 2:06–2:27 Label All Wires (this video)
- 4:12–5:29 Identify the Line (Hot) Wire
- 0:25–1:15 Identify Wires and Switch Terminals
Step 4: Install new 3-way switches
- 5:49–6:58 Wire a Three-Way Switch Circuit
- 17:43–19:32 Connect Wires to Second Switch (Method 2)
- 5:22–7:16 Wire the Primary Three-Way Switch
Step 5: Wire the light fixture
- 4:17–4:29 Connect Load Wire to Common (Second Switch Box)
- 2:47–2:56 Connect Common (Light) to Switch 2
- 0:04–0:08 Connect Second Switch to Light Fixture
Step 6: Install switch and fixture covers
- 3:20–3:58 Secure New Switch and Install Button Cover
- 7:25–8:09 Install New Fixture Cover
- 1:42–1:43 Install Light Switch Cover Plate
Step 7: Restore power and test operation
- 3:39–3:54 Restore Power and Test Functionality
- 7:09–8:19 Restore Power and Test
- 6:26–6:54 Restore Power and Test Switches
How to Wire a 3-way Switch for Stair Lights at the Top and Bottom
Outline for installing a 3-way switch system to control stair lights from both the top and bottom of the stairs.
Read the full guide Browse all guides
Planning this project? Shop Oak Valley Designs.

