Remove Existing Light Switch
From How to Wire a 3-way Switch for Stair Lights at the Top and Bottom · Step 2 of 7 · Video by Today's Homeowner with Danny Lipford

Showing 0:08–0:12 of the source video. Watch the full video with every moment.
What happens in this clip
Once the power is confirmed off, use a flat-head screwdriver to carefully remove the faceplate of the existing light switch. Then, use a Phillips-head or flat-head screwdriver (depending on the screw type) to unscrew the mounting screws that hold the switch body to the electrical box in the wall. Gently pull the existing light switch out of the electrical box, exposing the connected wires. Carefully disconnect the wires from the old switch. This usually involves loosening screw terminals or unwrapping wires from push-in terminals.
Goal: Disconnect and remove the old light switch
What's used
Tools
- Existing Light Switch
- Flat-head Screwdriver
- Non-contact Voltage Tester
About the full video
This project provides step-by-step instructions on how to replace a standard light switch with a dimmer switch. It covers essential safety precautions like turning off power, disconnecting the old switch, wiring the new dimmer, and finally installing and testing it for proper operation.
Step 2 of 7: Remove existing switch and light fixture
Unscrew the faceplate of the existing light switch. Carefully unscrew the switch from the electrical box, pulling it out to expose the wires. Note which wires are connected to the switch. Remove the light fixture canopy or cover to expose its wiring connections. Disconnect the wires from the light fixture.
Every video in How to Wire a 3-way Switch for Stair Lights at the Top and Bottom
Step 1: De-energize the circuit
- 0:08–0:36 Turn Off Circuit Breaker
- 0:03–0:08 Turn Off Power at Breaker Panel
- 2:06–2:13 Turn Off Power at Breaker
Step 2: Remove existing switch and light fixture
- 0:16–0:24 Remove Old Light Switch
- 17:23–17:28 Remove the old light switch
- 0:08–0:12 Remove Existing Light Switch (this video)
Step 3: Identify and label wires
- 2:06–2:27 Label All Wires
- 4:12–5:29 Identify the Line (Hot) Wire
- 0:25–1:15 Identify Wires and Switch Terminals
Step 4: Install new 3-way switches
- 5:49–6:58 Wire a Three-Way Switch Circuit
- 17:43–19:32 Connect Wires to Second Switch (Method 2)
- 5:22–7:16 Wire the Primary Three-Way Switch
Step 5: Wire the light fixture
- 4:17–4:29 Connect Load Wire to Common (Second Switch Box)
- 2:47–2:56 Connect Common (Light) to Switch 2
- 0:04–0:08 Connect Second Switch to Light Fixture
Step 6: Install switch and fixture covers
- 3:20–3:58 Secure New Switch and Install Button Cover
- 7:25–8:09 Install New Fixture Cover
- 1:42–1:43 Install Light Switch Cover Plate
Step 7: Restore power and test operation
- 3:39–3:54 Restore Power and Test Functionality
- 7:09–8:19 Restore Power and Test
- 6:26–6:54 Restore Power and Test Switches
Questions about How to Wire a 3-way Switch for Stair Lights at the Top and Bottom
How can I ensure I correctly identify and label the wires for a 3-way switch, especially for a beginner?
The most crucial step is identifying the 'common' wire, which is usually darker (black) and connected to a distinctively colored screw (often black or brass). The other two wires are 'travelers.' Use electrical tape or a marker to clearly label each wire immediately after identification, making sure not to confuse them between the two switch boxes.
What are the common reasons why a newly wired 3-way switch might not work, and how do I troubleshoot?
The most frequent issue is incorrectly wiring the common or traveler wires. If the light only works from one switch, or not at all, double-check that the common wire is correctly connected to the common terminal on both switches. Use your non-contact voltage tester to confirm power is reaching the switches and the fixture, and check all wire nuts for secure connections.
Is wiring a 3-way switch really a beginner-friendly project, and what's the realistic time commitment?
While labeled 'beginner,' it's more complex than a single-pole switch, requiring careful attention to wiring diagrams and wire identification. It's manageable for a patient beginner. The estimated 4 hours is a good realistic timeframe, especially for someone new to 3-way wiring, allowing for careful work and troubleshooting.
What are some alternative options or upgrades I could consider beyond a basic 3-way switch for stair lighting?
You could upgrade to dimmer-compatible 3-way switches to control light intensity, or consider smart 3-way switches for app or voice control. However, smart switches often require a neutral wire in the switch box, which might necessitate additional wiring work if your home is older and lacks one.
Do I need a permit or inspection for installing a 3-way switch system?
Local regulations vary, but any electrical work, even replacing switches, may require a permit and subsequent inspection in your area. Always check with your local building department or code enforcement office before starting the project to ensure compliance and avoid potential issues with home insurance or resale.
How to Wire a 3-way Switch for Stair Lights at the Top and Bottom
Outline for installing a 3-way switch system to control stair lights from both the top and bottom of the stairs.
Read the full guide Browse all guides
Planning this project? Shop Oak Valley Designs.

