Turn Off Power at Breaker Panel
From How to Wire a 3-way Switch for Stair Lights at the Top and Bottom · Step 1 of 7 · Video by Today's Homeowner with Danny Lipford

Showing 0:03–0:08 of the source video. Watch the full video with every moment.
What happens in this clip
Before beginning any electrical work, it is crucial to ensure that the power to the circuit you will be working on is completely off. Locate your home's main circuit breaker panel, which is typically found in a basement, garage, or utility closet. Consult the panel's legend or diagram to identify the circuit breaker that controls the light switch you intend to replace. Once identified, firmly flip the corresponding circuit breaker to the "OFF" position to de-energize the circuit.
Goal: De-energize the circuit for safety
What's used
Tools
- Circuit Breaker Panel
About the full video
This project provides step-by-step instructions on how to replace a standard light switch with a dimmer switch. It covers essential safety precautions like turning off power, disconnecting the old switch, wiring the new dimmer, and finally installing and testing it for proper operation.
Step 1 of 7: De-energize the circuit
Locate the circuit breaker that controls the stair lights and switch it to the 'OFF' position. If the circuit is not clearly labeled, turn off the main breaker to ensure all power is off.
Every video in How to Wire a 3-way Switch for Stair Lights at the Top and Bottom
Step 1: De-energize the circuit
- 0:08–0:36 Turn Off Circuit Breaker
- 0:03–0:08 Turn Off Power at Breaker Panel (this video)
- 2:06–2:13 Turn Off Power at Breaker
Step 2: Remove existing switch and light fixture
- 0:16–0:24 Remove Old Light Switch
- 17:23–17:28 Remove the old light switch
- 0:08–0:12 Remove Existing Light Switch
Step 3: Identify and label wires
- 2:06–2:27 Label All Wires
- 4:12–5:29 Identify the Line (Hot) Wire
- 0:25–1:15 Identify Wires and Switch Terminals
Step 4: Install new 3-way switches
- 5:49–6:58 Wire a Three-Way Switch Circuit
- 17:43–19:32 Connect Wires to Second Switch (Method 2)
- 5:22–7:16 Wire the Primary Three-Way Switch
Step 5: Wire the light fixture
- 4:17–4:29 Connect Load Wire to Common (Second Switch Box)
- 2:47–2:56 Connect Common (Light) to Switch 2
- 0:04–0:08 Connect Second Switch to Light Fixture
Step 6: Install switch and fixture covers
- 3:20–3:58 Secure New Switch and Install Button Cover
- 7:25–8:09 Install New Fixture Cover
- 1:42–1:43 Install Light Switch Cover Plate
Step 7: Restore power and test operation
- 3:39–3:54 Restore Power and Test Functionality
- 7:09–8:19 Restore Power and Test
- 6:26–6:54 Restore Power and Test Switches
Questions about How to Wire a 3-way Switch for Stair Lights at the Top and Bottom
How can I ensure I correctly identify and label the wires for a 3-way switch, especially for a beginner?
The most crucial step is identifying the 'common' wire, which is usually darker (black) and connected to a distinctively colored screw (often black or brass). The other two wires are 'travelers.' Use electrical tape or a marker to clearly label each wire immediately after identification, making sure not to confuse them between the two switch boxes.
What are the common reasons why a newly wired 3-way switch might not work, and how do I troubleshoot?
The most frequent issue is incorrectly wiring the common or traveler wires. If the light only works from one switch, or not at all, double-check that the common wire is correctly connected to the common terminal on both switches. Use your non-contact voltage tester to confirm power is reaching the switches and the fixture, and check all wire nuts for secure connections.
Is wiring a 3-way switch really a beginner-friendly project, and what's the realistic time commitment?
While labeled 'beginner,' it's more complex than a single-pole switch, requiring careful attention to wiring diagrams and wire identification. It's manageable for a patient beginner. The estimated 4 hours is a good realistic timeframe, especially for someone new to 3-way wiring, allowing for careful work and troubleshooting.
What are some alternative options or upgrades I could consider beyond a basic 3-way switch for stair lighting?
You could upgrade to dimmer-compatible 3-way switches to control light intensity, or consider smart 3-way switches for app or voice control. However, smart switches often require a neutral wire in the switch box, which might necessitate additional wiring work if your home is older and lacks one.
Do I need a permit or inspection for installing a 3-way switch system?
Local regulations vary, but any electrical work, even replacing switches, may require a permit and subsequent inspection in your area. Always check with your local building department or code enforcement office before starting the project to ensure compliance and avoid potential issues with home insurance or resale.
How to Wire a 3-way Switch for Stair Lights at the Top and Bottom
Outline for installing a 3-way switch system to control stair lights from both the top and bottom of the stairs.
Read the full guide Browse all guides
Planning this project? Shop Oak Valley Designs.

