Determine Stringer Attachment to Deck Band Board
From How to Build Basement Stairs · Step 3 of 9 · Video by Perkins Builder Brothers

Showing 5:17–6:26 of the source video. Watch the full video with every moment.
What happens in this clip
Observe the underside of the deck's band board where the top of the stringer will meet. If there is insufficient wood material (less than a few inches) below the decking to securely attach the stringer directly, you will need to add a piece of blocking (cleat) to the band board or utilize a specialized joist hanger. This ensures a robust connection capable of supporting the staircase's weight and dynamic loads.
Goal: Assess the available space on the deck's band board for stringer attachment. If there isn't enough material for direct attachment, plan to add supplementary blocking or use specialized joist hangers to ensure a secure connection.
What's used
Tools
- Level
Materials
- Joist Hangers
- Pressure-Treated Lumber (Blocking)
About the full video
This video provides a detailed guide on constructing a sturdy outdoor staircase landing, focusing on precise measurements, proper stringer layout, and an innovative method for integrating concrete footings. It also covers the installation of railing components and important considerations for working with pressure-treated lumber.
What's said in this clip
i mean how hard can it be you made me think of a question here i have seen sometimes when people build the first step actually flush with the deck yeah yeah i have seen that no i'm not sure why you would do that can you think of a reason i mean there might be a good reason why it makes the railing work out weird because the railing has to go up and then flatten out you'd almost have to put another post right here or something weird right for the railing to stay at the same height uh parallel to the top of the step angle well it might be somebody just looking at this and thinking there's nothing to hang the stringer to down here well there is very little obviously the line is right there we have almost two inches yeah so we have to add something down here like that will allow us to attach the stringer so if you didn't think okay i can add something here you would think oh my stringer needs to butt here and that would be a great place i mean there's lots of room you know yeah but i think that looks a little goofy i like coming off with the first step being down from here not out well and it makes the steps stick out farther it does yeah in a lot of cases restrictions yeah that's a that's a good point i don't think we've ever talked about that in a video i think that'd be the main reason someone did it though
Automatically transcribed from the source video.
Step 3 of 9: Install Top Support for Stringers
At the top of the stair opening, where the stringers will meet the upper level, install a strong support. This can be a pressure-treated ledger board bolted to the subfloor and rim joist, or solid wood blocking installed between the joists. Ensure this support is exceptionally strong as it will bear a significant portion of the stair's load. The ledger board should be level and flush with the edge of the opening where the stringers will sit.
Every video in How to Build Basement Stairs
Step 1: Measure and Plan Stair Location
- 1:14–1:25 Measure and Calculate Stair Dimensions
- 0:11–1:48 Calculate and Layout Staircase Dimensions
- 0:00–2:15 Calculate Stair Dimensions
Step 2: Cut Stair Stringers
- 0:57–1:08 Lay Out and Cut the First Stringer
- 5:24–6:18 Cut Stair Stringers from Lumber
- 2:20–3:14 Mark and Cut Stringers
Step 3: Install Top Support for Stringers
- 12:25–12:49 Install Ledger Board for Stringers
- 5:17–6:26 Determine Stringer Attachment to Deck Band Board (this video)
- 13:16–13:26 Attach Stair Stringer Ledger
Step 4: Attach Stringers to Top Support
- 30:00–35:46 Install Stringers and Brackets
- 6:49–8:07 Install Stringers
- 9:15–10:09 Installing Stringer Hangers to Deck
Step 5: Secure Bottom of Stringers
- 10:09–11:12 Securing Stringers to Landing Pad with Base Plate
- 9:41–10:36 Anchor Stringer Base Plate to Concrete
- 18:03–22:29 Secure Staircase Bottom
Step 6: Cut and Install Treads
- 10:15–17:22 Install Risers and Treads
- 10:10–11:50 Apply Adhesive and Install Treads
- 0:06–0:09 Install Treads and Risers
Step 7: Cut and Install Risers (Optional but Recommended)
- 30:57–33:30 Install Stair Risers
- 8:38–11:15 Install Risers
- 0:06–0:09 Install Treads and Risers
Step 8: Install Handrails and Balusters
- 0:32–0:45 Install Handrails
- 5:36–6:05 Install Balusters and Handrail
- 11:30–13:16 Install Balusters
Step 9: Sand and Finish Treads and Risers
- 0:37–0:41 Sand the Staircase
- 8:53–11:22 Sand and Finish Stairs
- 0:08–1:13 Prepare and Finish Wood Stair Treads
Questions about How to Build Basement Stairs
What are the most critical building code requirements I need to understand for safe basement stairs?
Focus on consistent rise and run dimensions for each step, minimum tread depth, maximum riser height, minimum headroom clearance, handrail height, and baluster spacing. These vary by location, so always consult your local building department for specific requirements before starting your project to ensure compliance and safety.
Are specialized tools like stair gauges and an orbital sander truly necessary for building basement stairs?
Yes, stair gauges are highly recommended as they attach to your framing square, ensuring precise, repeatable cuts for consistent rise and run on your stringers, which is crucial for safety. An orbital sander significantly speeds up and improves the finish quality of your treads and risers, making the final product look professional.
What's the most challenging part of building basement stairs for an intermediate DIYer, and how can I prepare for it?
The most challenging part is accurately laying out and cutting the stringers, as even slight inconsistencies can lead to uneven, unsafe steps. Prepare by double-checking all measurements, using stair gauges for precision, making a practice cut on a scrap piece, and taking your time to ensure perfect angles and lengths.
What common mistakes do DIYers make when building stair stringers, and how can I avoid them?
A common mistake is incorrect calculations or cuts leading to an inconsistent rise or run, creating a tripping hazard. Avoid this by meticulously measuring your total rise, calculating the exact individual rise and run, using stair gauges correctly, and dry-fitting your layout before making final cuts on all stringers.
Why is selecting 'premium lumber' important for stair stringers, and what should I look for?
Premium lumber, typically 2x12s, is crucial for stringers because it has fewer knots and straighter grain, reducing the chance of warping or weakness. Look for boards that are straight, free of large knots, cracks, or excessive bowing, as these defects can compromise the structural integrity and appearance of your stairs.
Is it better to sand and finish the treads and risers before or after installing them?
Sanding and finishing treads and risers before installation is generally easier and produces a more uniform finish, especially if you're staining. It prevents drips onto other surfaces and allows you to work comfortably. However, you'll need to be very careful during installation to avoid damaging the finished surfaces.
How to Build Basement Stairs
This project outlines the steps for building a safe and code-compliant set of stairs to a basement. It covers planning, material selection, cutting, assembly, and finishing, emphasizing structural integrity and safety features.
Read the full guide Browse all guides
Planning this project? Shop Oak Valley Designs.

