Lay Out and Cut the First Stringer
From How to Build Basement Stairs · Step 2 of 9 · Video by decks.com

Showing 0:57–1:08 of the source video. Watch the full video with every moment.
What happens in this clip
Obtain a 2x12 piece of lumber for the stringer. Using a framing square, carefully transfer the calculated rise and run dimensions onto the 2x12, marking all cut lines with a pencil. After marking, use a circular saw to meticulously cut along these lines to create the first stringer. This initial stringer is critical as it will serve as a template; use it to accurately trace and cut all subsequent stringers, ensuring consistency across the entire staircase.
Goal: Accurately cut the first stringer to serve as a template for all others.
What's used
Tools
- 2x12 Lumber
- Circular Saw
- but less efficient for long straight lines)
- Framing Square
- Pencil
About the full video
This project provides a comprehensive, step-by-step guide to constructing and installing deck stairs. It covers initial measurements, calculating rise and run for stringers, cutting the stringers, two methods for attaching stringers to the deck frame, and finally, installing the decking boards for treads and risers.
Step 2 of 9: Cut Stair Stringers
Select straight, knot-free 2x12 lumber for your stringers. Using your framing square and pencil, carefully lay out the rise and run for each step according to your calculations. Start from the top and mark out each step's dimensions. Make straight, clean cuts for each riser and tread. You will typically need two stringers, but for wider stairs, a third stringer in the middle is recommended for support. Ensure the 'notch' for the landing at the top is properly cut to rest securely on the subfloor or header. The bottom of the stringer should sit flat on the basement floor, or on a properly prepared landing.
Every video in How to Build Basement Stairs
Step 1: Measure and Plan Stair Location
- 1:14–1:25 Measure and Calculate Stair Dimensions
- 0:11–1:48 Calculate and Layout Staircase Dimensions
- 0:00–2:15 Calculate Stair Dimensions
Step 2: Cut Stair Stringers
- 0:57–1:08 Lay Out and Cut the First Stringer (this video)
- 5:24–6:18 Cut Stair Stringers from Lumber
- 2:20–3:14 Mark and Cut Stringers
Step 3: Install Top Support for Stringers
- 12:25–12:49 Install Ledger Board for Stringers
- 5:17–6:26 Determine Stringer Attachment to Deck Band Board
- 13:16–13:26 Attach Stair Stringer Ledger
Step 4: Attach Stringers to Top Support
- 30:00–35:46 Install Stringers and Brackets
- 6:49–8:07 Install Stringers
- 9:15–10:09 Installing Stringer Hangers to Deck
Step 5: Secure Bottom of Stringers
- 10:09–11:12 Securing Stringers to Landing Pad with Base Plate
- 9:41–10:36 Anchor Stringer Base Plate to Concrete
- 18:03–22:29 Secure Staircase Bottom
Step 6: Cut and Install Treads
- 10:15–17:22 Install Risers and Treads
- 10:10–11:50 Apply Adhesive and Install Treads
- 0:06–0:09 Install Treads and Risers
Step 7: Cut and Install Risers (Optional but Recommended)
- 30:57–33:30 Install Stair Risers
- 8:38–11:15 Install Risers
- 0:06–0:09 Install Treads and Risers
Step 8: Install Handrails and Balusters
- 0:32–0:45 Install Handrails
- 5:36–6:05 Install Balusters and Handrail
- 11:30–13:16 Install Balusters
Step 9: Sand and Finish Treads and Risers
- 0:37–0:41 Sand the Staircase
- 8:53–11:22 Sand and Finish Stairs
- 0:08–1:13 Prepare and Finish Wood Stair Treads
How to Build Basement Stairs
This project outlines the steps for building a safe and code-compliant set of stairs to a basement. It covers planning, material selection, cutting, assembly, and finishing, emphasizing structural integrity and safety features.
Read the full guide Browse all guides
Planning this project? Shop Oak Valley Designs.

