Anchor Stringer Base Plate to Concrete
From How to Build Basement Stairs · Step 5 of 9 · Video by BYOT

Showing 9:41–10:36 of the source video. Watch the full video with every moment.
What happens in this clip
Position a 2x8 pressure-treated lumber board (cut to the correct width) underneath the bottom notches of the stringers, resting on the concrete landing. Ensure it's perfectly level and aligned with the stringers. This serves as a base plate. Using an impact driver with a 1/2-inch concrete drill bit, drill through the base plate and deeply into the concrete. After drilling, use a shop vac to remove all concrete dust and debris from the holes to ensure a strong grip. Insert 1/2-inch wedge anchors into the drilled holes, hammering them down fully. Use a ratchet to tighten the wedge anchors as much as possible, firmly securing the base plate to the concrete. This provides crucial stability and prevents movement of the stair stringers at the base.
Goal: Secure the bottom base plate of the stringers to the concrete landing using an impact driver, concrete drill bit, and wedge anchors.
What's used
Tools
- 1/2-inch Concrete Drill Bit
- Hammer
- Impact Driver
- Level
- Ratchet
- Shop Vac
Materials
- 1/2-inch Wedge Anchors
- 2x8 Pressure-Treated Lumber
- Shims (Composite)
About the full video
This video details the process of installing perfect deck stairs by accurately calculating rise and run, notching stringers from pressure-treated lumber, reinforcing the deck's structure, installing composite treads and risers, and finishing with protective fascia boards. The process emphasizes precise measurements, proper cutting techniques, and secure fastening for a durable and aesthetically pleasing staircase.
What's said in this clip
DeckWise decking spacers. As I descend to the last step, I realize that I probably should have secured the bottom support plate to the concrete before I started installing the steps and risers. But it wouldn't hurt to do it at this stage. To do this, I take a screwdriver with a half-inch concrete drill bit and drill a hole through the backing plate directly into the concrete. Just make sure you vacuum up as much concrete dust as possible before moving on to the wedge anchors. These are half-inch wedge anchors that are designed specifically for this type of fastening and are extremely strong. After I drive the anchor all the way in . I take the ratchet wrench and tighten it as hard as I can. Then I move to the other side. I follow the same process. And now this support plate will definitely not move anywhere. Keep in mind that this support plate is not only needed for structural strength , it also protects
Automatically transcribed from the source video.
Step 5 of 9: Secure Bottom of Stringers
The bottom of the stringers must be firmly secured to prevent the stairs from shifting or tipping. If resting on a concrete slab, you can use concrete anchors (like Tapcons) to secure wooden blocks to the slab, and then screw the stringers to these blocks. If resting on a wooden subfloor or a framed landing, attach solid wood blocking or a sturdy footing to the subfloor, and then secure the stringers to this blocking using screws or hangers. Ensure the stringers are plumb and properly spaced before final fastening.
Every video in How to Build Basement Stairs
Step 1: Measure and Plan Stair Location
- 1:14–1:25 Measure and Calculate Stair Dimensions
- 0:11–1:48 Calculate and Layout Staircase Dimensions
- 0:00–2:15 Calculate Stair Dimensions
Step 2: Cut Stair Stringers
- 0:57–1:08 Lay Out and Cut the First Stringer
- 5:24–6:18 Cut Stair Stringers from Lumber
- 2:20–3:14 Mark and Cut Stringers
Step 3: Install Top Support for Stringers
- 12:25–12:49 Install Ledger Board for Stringers
- 5:17–6:26 Determine Stringer Attachment to Deck Band Board
- 13:16–13:26 Attach Stair Stringer Ledger
Step 4: Attach Stringers to Top Support
- 30:00–35:46 Install Stringers and Brackets
- 6:49–8:07 Install Stringers
- 9:15–10:09 Installing Stringer Hangers to Deck
Step 5: Secure Bottom of Stringers
- 10:09–11:12 Securing Stringers to Landing Pad with Base Plate
- 9:41–10:36 Anchor Stringer Base Plate to Concrete (this video)
- 18:03–22:29 Secure Staircase Bottom
Step 6: Cut and Install Treads
- 10:15–17:22 Install Risers and Treads
- 10:10–11:50 Apply Adhesive and Install Treads
- 0:06–0:09 Install Treads and Risers
Step 7: Cut and Install Risers (Optional but Recommended)
- 30:57–33:30 Install Stair Risers
- 8:38–11:15 Install Risers
- 0:06–0:09 Install Treads and Risers
Step 8: Install Handrails and Balusters
- 0:32–0:45 Install Handrails
- 5:36–6:05 Install Balusters and Handrail
- 11:30–13:16 Install Balusters
Step 9: Sand and Finish Treads and Risers
- 0:37–0:41 Sand the Staircase
- 8:53–11:22 Sand and Finish Stairs
- 0:08–1:13 Prepare and Finish Wood Stair Treads
How to Build Basement Stairs
This project outlines the steps for building a safe and code-compliant set of stairs to a basement. It covers planning, material selection, cutting, assembly, and finishing, emphasizing structural integrity and safety features.
Read the full guide Browse all guides
Planning this project? Shop Oak Valley Designs.

