Cut Stair Stringers from Lumber
From How to Build Basement Stairs · Step 2 of 9 · Video by Kens Karpentry

Showing 5:24–6:18 of the source video. Watch the full video with every moment.
What happens in this clip
Using a framing square set to your calculated rise (8 inches) and run (9 inches), mark the step pattern onto long pieces of 2x12 lumber. Carefully cut along these lines. The builder uses a circular saw for the initial straight cuts along the top and bottom of each step, and then switches to a reciprocating saw (Sawzall) for the inside corners. This combination of tools allows for both speed on straight lines and precision in the tighter, notched areas, resulting in a crisp, clean finish for the stringers. Once the first stringer is cut, it can be used as a template to mark and cut subsequent stringers, ensuring consistency.
Goal: Mark and cut the stair stringers, first using a circular saw for rough cuts and then a reciprocating saw for precise inside corners.
What's used
Tools
- 2x12 Lumber
- Circular Saw
- Framing Square
- Pencil
- Reciprocating Saw (Sawzall)
- Sawhorses
About the full video
This video provides a detailed guide on constructing a sturdy staircase landing and integrating stair stringers using joist hangers for robust support. The project involves calculating rise and run, building a modular landing frame, installing it against existing wall studs, cutting custom stair stringers, installing a header with joist hangers, and finally securing the stringers and adding the treads.
What's said in this clip
i still have to make those okay so this one came out right on so now we'll use it as a template for the other side then we'll have both springers the same i like to cut these out with a sawzall because it gives a nice crisp inside corner yeah inside corner we are ready to put them up let's go inside and look
Automatically transcribed from the source video.
Step 2 of 9: Cut Stair Stringers
Select straight, knot-free 2x12 lumber for your stringers. Using your framing square and pencil, carefully lay out the rise and run for each step according to your calculations. Start from the top and mark out each step's dimensions. Make straight, clean cuts for each riser and tread. You will typically need two stringers, but for wider stairs, a third stringer in the middle is recommended for support. Ensure the 'notch' for the landing at the top is properly cut to rest securely on the subfloor or header. The bottom of the stringer should sit flat on the basement floor, or on a properly prepared landing.
Every video in How to Build Basement Stairs
Step 1: Measure and Plan Stair Location
- 1:14–1:25 Measure and Calculate Stair Dimensions
- 0:11–1:48 Calculate and Layout Staircase Dimensions
- 0:00–2:15 Calculate Stair Dimensions
Step 2: Cut Stair Stringers
- 0:57–1:08 Lay Out and Cut the First Stringer
- 5:24–6:18 Cut Stair Stringers from Lumber (this video)
- 2:20–3:14 Mark and Cut Stringers
Step 3: Install Top Support for Stringers
- 12:25–12:49 Install Ledger Board for Stringers
- 5:17–6:26 Determine Stringer Attachment to Deck Band Board
- 13:16–13:26 Attach Stair Stringer Ledger
Step 4: Attach Stringers to Top Support
- 30:00–35:46 Install Stringers and Brackets
- 6:49–8:07 Install Stringers
- 9:15–10:09 Installing Stringer Hangers to Deck
Step 5: Secure Bottom of Stringers
- 10:09–11:12 Securing Stringers to Landing Pad with Base Plate
- 9:41–10:36 Anchor Stringer Base Plate to Concrete
- 18:03–22:29 Secure Staircase Bottom
Step 6: Cut and Install Treads
- 10:15–17:22 Install Risers and Treads
- 10:10–11:50 Apply Adhesive and Install Treads
- 0:06–0:09 Install Treads and Risers
Step 7: Cut and Install Risers (Optional but Recommended)
- 30:57–33:30 Install Stair Risers
- 8:38–11:15 Install Risers
- 0:06–0:09 Install Treads and Risers
Step 8: Install Handrails and Balusters
- 0:32–0:45 Install Handrails
- 5:36–6:05 Install Balusters and Handrail
- 11:30–13:16 Install Balusters
Step 9: Sand and Finish Treads and Risers
- 0:37–0:41 Sand the Staircase
- 8:53–11:22 Sand and Finish Stairs
- 0:08–1:13 Prepare and Finish Wood Stair Treads
How to Build Basement Stairs
This project outlines the steps for building a safe and code-compliant set of stairs to a basement. It covers planning, material selection, cutting, assembly, and finishing, emphasizing structural integrity and safety features.
Read the full guide Browse all guides
Planning this project? Shop Oak Valley Designs.

