Cut Miter Joints for Outside Corner
From How to Install Baseboard Along a Staircase Wall · Step 5 of 9 · Video by VCG Construction

Showing 0:12–0:19 of the source video. Watch the full video with every moment.
What happens in this clip
Once the trim board is marked, take it to a miter saw. For an outside 90-degree corner, each piece of trim will require a 45-degree miter cut. Adjust the miter saw to a 45-degree angle. Ensure the cut is made on the correct side of the pencil mark to account for the angle and the length of the trim. The two 45-degree cuts from each trim piece will join together to form a crisp 90-degree outside corner. After cutting, test-fit the two pieces together to ensure a tight seam.
Goal: Make the necessary miter cuts on the trim boards using a miter saw to form a perfect 90-degree outside corner.
What's used
Tools
- Miter Saw
- Trim Board
About the full video
This video provides instructions on how to create precise outside corner joints for door casing using a miter saw, pre-assembling them for a professional finish, and then installing them. It also briefly touches upon the approach for inside corners with base cap.
Step 5 of 9: Cut Inside and Outside Corners
For corners, you will need to make miter cuts. For an inside corner, set your miter saw to 45 degrees (or the appropriate angle for your corner) and cut away from the piece. For an outside corner, also set your miter saw to 45 degrees but cut towards the piece. The goal is to create two beveled edges that meet perfectly to form the corner. Ensure your cuts are precise, as even a small error will be noticeable.
Every video in How to Install Baseboard Along a Staircase Wall
Step 1: Measure and Plan Baseboard Layout
- 0:21–0:35 Plan Room Layout and Measure Walls
- 0:00–0:24 Measure Wall and Plan Baseboard Layout
- 0:49–2:35 Prepare the Room and Measure Baseboard Lengths
Step 2: Acquire Baseboard Material
Step 3: Prepare the Wall Surface
- 0:16–0:29 Prepare Wall and Floor
- 1:43–2:45 Prepare Wall Surface by Removing Residue
- 0:13–0:18 Test Fit and Refine Cuts
Step 4: Make Initial Straight Cuts
- 0:18–0:22 Measure and Cut Trim
- 0:12–0:14 Make the Horizontal and Second Vertical Cuts
- 0:08–0:11 Extend Marks and Make First Cut
Step 5: Cut Inside and Outside Corners
- 1:33–1:49 Miter Cut for Second Outside Corner Piece
- 0:12–0:19 Cut Miter Joints for Outside Corner (this video)
- 0:11–0:25 Perform the 45-Degree Miter Cuts
Step 6: Dry Fit and Adjust Cuts
- 1:03–1:15 Dry Fit Baseboards Around Room
- 0:18–0:24 Test Fit and Adjust
- 0:19–0:25 Final Dry-Fit and Installation
Step 7: Install the Baseboard Molding
- 8:34–9:59 Install Baseboard
- 0:16–0:22 Mark Stud Locations and Install Baseboard
- 0:08–0:14 Install Baseboards to the Wall
Step 8: Fill Nail Holes and Caulk Gaps
- 1:31–1:41 Fill Nail Holes and Caulk Seams
- 22:02–25:10 Finish Baseboards (Fill, Caulk, Paint)
- 0:00–0:04 Fill Nail Holes with Wood Putty
Step 9: Paint or Finish Baseboard
- 22:02–25:10 Finish Baseboards (Fill, Caulk, Paint)
- 1:41–1:52 Apply Final Touch-Up Paint
- 9:00–9:16 Touch-Up Paint Filled Areas
How to Install Baseboard Along a Staircase Wall
A high-level outline for installing baseboard molding along a staircase wall, including planning, cutting, fitting, and finishing steps.
Read the full guide Browse all guides
Planning this project? Shop Oak Valley Designs.

