Extend Marks and Make First Cut
From How to Install Baseboard Along a Staircase Wall · Step 4 of 9 · Video by Hard Work

Showing 0:08–0:11 of the source video. Watch the full video with every moment.
What happens in this clip
Use a ruler or a square to extend the previously made marks across the full width of the baseboard. Carefully cut along these extended lines. The video suggests using a miter saw or jigsaw for this cut. This will remove a rectangular section from the bottom of the baseboard, creating the first 'step' in the trim.
Goal: Cut out the first section of the baseboard to match the lower step.
What's used
Tools
- Baseboard Piece
- Marker
- Miter Saw
- Hand saw with miter box
- Ruler
- T-square
- Safety Glasses
About the full video
This DIY project demonstrates a precise method for cutting and fitting baseboard around external stair corners, creating a continuous, stepped profile. It involves careful measurement, marking, and cutting to achieve a professional, snug fit for a polished look.
Step 4 of 9: Make Initial Straight Cuts
Using a miter saw or a hand saw with a miter box, cut the baseboard molding to the lengths needed for the straight runs along the staircase wall. Measure each section precisely and make clean, straight cuts. If you are using a miter saw, set it to 0 degrees for a square cut. If using a hand saw and miter box, ensure the saw follows the 90-degree slot.
Every video in How to Install Baseboard Along a Staircase Wall
Step 1: Measure and Plan Baseboard Layout
- 0:21–0:35 Plan Room Layout and Measure Walls
- 0:00–0:24 Measure Wall and Plan Baseboard Layout
- 0:49–2:35 Prepare the Room and Measure Baseboard Lengths
Step 2: Acquire Baseboard Material
Step 3: Prepare the Wall Surface
- 0:16–0:29 Prepare Wall and Floor
- 1:43–2:45 Prepare Wall Surface by Removing Residue
- 0:13–0:18 Test Fit and Refine Cuts
Step 4: Make Initial Straight Cuts
- 0:18–0:22 Measure and Cut Trim
- 0:12–0:14 Make the Horizontal and Second Vertical Cuts
- 0:08–0:11 Extend Marks and Make First Cut (this video)
Step 5: Cut Inside and Outside Corners
- 1:33–1:49 Miter Cut for Second Outside Corner Piece
- 0:12–0:19 Cut Miter Joints for Outside Corner
- 0:11–0:25 Perform the 45-Degree Miter Cuts
Step 6: Dry Fit and Adjust Cuts
- 1:03–1:15 Dry Fit Baseboards Around Room
- 0:18–0:24 Test Fit and Adjust
- 0:19–0:25 Final Dry-Fit and Installation
Step 7: Install the Baseboard Molding
- 8:34–9:59 Install Baseboard
- 0:16–0:22 Mark Stud Locations and Install Baseboard
- 0:08–0:14 Install Baseboards to the Wall
Step 8: Fill Nail Holes and Caulk Gaps
- 1:31–1:41 Fill Nail Holes and Caulk Seams
- 22:02–25:10 Finish Baseboards (Fill, Caulk, Paint)
- 0:00–0:04 Fill Nail Holes with Wood Putty
Step 9: Paint or Finish Baseboard
- 22:02–25:10 Finish Baseboards (Fill, Caulk, Paint)
- 1:41–1:52 Apply Final Touch-Up Paint
- 9:00–9:16 Touch-Up Paint Filled Areas
How to Install Baseboard Along a Staircase Wall
A high-level outline for installing baseboard molding along a staircase wall, including planning, cutting, fitting, and finishing steps.
Read the full guide Browse all guides
Planning this project? Shop Oak Valley Designs.

