Mark Stud Locations and Install Baseboard
From How to Install Baseboard Along a Staircase Wall · Step 7 of 9 · Video by Home Repair Tutor

Showing 0:16–0:22 of the source video. Watch the full video with every moment.
What happens in this clip
After cutting, dry-fit the baseboard to ensure it fits correctly. Then, temporarily place the baseboard against the wall and use a pencil to mark the locations of the wall studs onto the tile or wall. This helps ensure that the baseboard is nailed into structural support rather than just drywall. Once the stud locations are marked, position the baseboard and use a cordless nailer to securely fasten it to the wall, aligning the nails with the marked stud locations. This provides a strong and stable installation.
Goal: Securely fasten the baseboard to the wall, aligning with stud locations.
What's used
Tools
- Baseboard
- Cordless Nailer Milwaukee
- Hammer and finish nails (requires pre-drilling to prevent splitting)
- Pencil
- Stud finder (not shown
- but recommended for accuracy)
Materials
- Finish Nails
About the full video
This project demonstrates how to precisely install baseboard trim in a bathroom, particularly around a heat register that is not perfectly aligned at a 90-degree angle. It involves using a T-bevel to measure and transfer an irregular angle, cutting the baseboard with a miter saw, and then securely fastening it to the wall with a cordless nailer for a tight, professional fit.
Step 7 of 9: Install the Baseboard Molding
Once you are satisfied with the fit, begin the permanent installation. Apply a bead of construction adhesive to the back of each baseboard section. Then, press the molding firmly against the wall. For added security, use a nail gun with finishing nails to secure the baseboard to the wall studs. Drive the nails flush or slightly below the surface of the molding. Work from one end of the staircase to the other, ensuring each piece is aligned correctly.
Every video in How to Install Baseboard Along a Staircase Wall
Step 1: Measure and Plan Baseboard Layout
- 0:21–0:35 Plan Room Layout and Measure Walls
- 0:00–0:24 Measure Wall and Plan Baseboard Layout
- 0:49–2:35 Prepare the Room and Measure Baseboard Lengths
Step 2: Acquire Baseboard Material
Step 3: Prepare the Wall Surface
- 0:16–0:29 Prepare Wall and Floor
- 1:43–2:45 Prepare Wall Surface by Removing Residue
- 0:13–0:18 Test Fit and Refine Cuts
Step 4: Make Initial Straight Cuts
- 0:18–0:22 Measure and Cut Trim
- 0:12–0:14 Make the Horizontal and Second Vertical Cuts
- 0:08–0:11 Extend Marks and Make First Cut
Step 5: Cut Inside and Outside Corners
- 1:33–1:49 Miter Cut for Second Outside Corner Piece
- 0:12–0:19 Cut Miter Joints for Outside Corner
- 0:11–0:25 Perform the 45-Degree Miter Cuts
Step 6: Dry Fit and Adjust Cuts
- 1:03–1:15 Dry Fit Baseboards Around Room
- 0:18–0:24 Test Fit and Adjust
- 0:19–0:25 Final Dry-Fit and Installation
Step 7: Install the Baseboard Molding
- 8:34–9:59 Install Baseboard
- 0:16–0:22 Mark Stud Locations and Install Baseboard (this video)
- 0:08–0:14 Install Baseboards to the Wall
Step 8: Fill Nail Holes and Caulk Gaps
- 1:31–1:41 Fill Nail Holes and Caulk Seams
- 22:02–25:10 Finish Baseboards (Fill, Caulk, Paint)
- 0:00–0:04 Fill Nail Holes with Wood Putty
Step 9: Paint or Finish Baseboard
- 22:02–25:10 Finish Baseboards (Fill, Caulk, Paint)
- 1:41–1:52 Apply Final Touch-Up Paint
- 9:00–9:16 Touch-Up Paint Filled Areas
How to Install Baseboard Along a Staircase Wall
A high-level outline for installing baseboard molding along a staircase wall, including planning, cutting, fitting, and finishing steps.
Read the full guide Browse all guides
Planning this project? Shop Oak Valley Designs.

