Measure and Cut Trim
From How to Install Baseboard Along a Staircase Wall · Step 4 of 9 · Video by Better Homes and Gardens

Showing 0:18–0:22 of the source video. Watch the full video with every moment.
What happens in this clip
Using a tape measure, accurately determine the length of each section of wall where baseboard trim will be installed. Transfer these measurements to the baseboard pieces, marking the cut lines precisely with a pencil. Then, use an appropriate cutting tool, such as a miter saw or a handsaw with a miter box, to cut the trim to the correct lengths. Ensure all cuts are clean and precise for seamless corners and joints.
Goal: Cut baseboard trim to fit wall sections
What's used
Tools
- Baseboard Trim
- Miter Saw Not visible
- Pencil
- Tape Measure
- Steel rule
About the full video
This project provides step-by-step instructions on how to install baseboard trim using traditional tools like a hammer and nails. It covers everything from preparing the room and acclimating the wood to locating studs, cutting trim, securely nailing it, filling nail holes, and preparing the surface for a final finish.
Step 4 of 9: Make Initial Straight Cuts
Using a miter saw or a hand saw with a miter box, cut the baseboard molding to the lengths needed for the straight runs along the staircase wall. Measure each section precisely and make clean, straight cuts. If you are using a miter saw, set it to 0 degrees for a square cut. If using a hand saw and miter box, ensure the saw follows the 90-degree slot.
Every video in How to Install Baseboard Along a Staircase Wall
Step 1: Measure and Plan Baseboard Layout
- 0:21–0:35 Plan Room Layout and Measure Walls
- 0:00–0:24 Measure Wall and Plan Baseboard Layout
- 0:49–2:35 Prepare the Room and Measure Baseboard Lengths
Step 2: Acquire Baseboard Material
Step 3: Prepare the Wall Surface
- 0:16–0:29 Prepare Wall and Floor
- 1:43–2:45 Prepare Wall Surface by Removing Residue
- 0:13–0:18 Test Fit and Refine Cuts
Step 4: Make Initial Straight Cuts
- 0:18–0:22 Measure and Cut Trim (this video)
- 0:12–0:14 Make the Horizontal and Second Vertical Cuts
- 0:08–0:11 Extend Marks and Make First Cut
Step 5: Cut Inside and Outside Corners
- 1:33–1:49 Miter Cut for Second Outside Corner Piece
- 0:12–0:19 Cut Miter Joints for Outside Corner
- 0:11–0:25 Perform the 45-Degree Miter Cuts
Step 6: Dry Fit and Adjust Cuts
- 1:03–1:15 Dry Fit Baseboards Around Room
- 0:18–0:24 Test Fit and Adjust
- 0:19–0:25 Final Dry-Fit and Installation
Step 7: Install the Baseboard Molding
- 8:34–9:59 Install Baseboard
- 0:16–0:22 Mark Stud Locations and Install Baseboard
- 0:08–0:14 Install Baseboards to the Wall
Step 8: Fill Nail Holes and Caulk Gaps
- 1:31–1:41 Fill Nail Holes and Caulk Seams
- 22:02–25:10 Finish Baseboards (Fill, Caulk, Paint)
- 0:00–0:04 Fill Nail Holes with Wood Putty
Step 9: Paint or Finish Baseboard
- 22:02–25:10 Finish Baseboards (Fill, Caulk, Paint)
- 1:41–1:52 Apply Final Touch-Up Paint
- 9:00–9:16 Touch-Up Paint Filled Areas
How to Install Baseboard Along a Staircase Wall
A high-level outline for installing baseboard molding along a staircase wall, including planning, cutting, fitting, and finishing steps.
Read the full guide Browse all guides
Planning this project? Shop Oak Valley Designs.

