Install Baseboards to the Wall
From How to Install Baseboard Along a Staircase Wall · Step 7 of 9 · Video by NikandLivDIY

Showing 0:08–0:14 of the source video. Watch the full video with every moment.
What happens in this clip
Position each baseboard piece firmly against the wall and down onto the floor, ensuring the silicone bead makes good contact. Use a brad nailer (or finish nailer) to secure the baseboard to the wall. Drive nails into the wall studs for maximum hold, typically placing one nail near the top and one near the bottom edge of the baseboard every 16 to 24 inches. If studs are not accessible or you desire extra security, apply a small amount of construction adhesive to the back of the baseboard before positioning it.
Goal: Secure baseboards firmly to the wall
What's used
Tools
- Air Compressor
- Brad Nailer
- Hammer and finish nails
- Stud Finder
Materials
- Baseboards
- Brad Nails
About the full video
This project provides a concise guide on how to install baseboards, focusing on the key techniques for achieving a professional finish. It covers cutting precise 45-degree angles for both inside and outside corners, applying silicone for water resistance, securing the baseboards with a nail gun, and finishing with a top caulk bead for a seamless look.
Step 7 of 9: Install the Baseboard Molding
Once you are satisfied with the fit, begin the permanent installation. Apply a bead of construction adhesive to the back of each baseboard section. Then, press the molding firmly against the wall. For added security, use a nail gun with finishing nails to secure the baseboard to the wall studs. Drive the nails flush or slightly below the surface of the molding. Work from one end of the staircase to the other, ensuring each piece is aligned correctly.
Every video in How to Install Baseboard Along a Staircase Wall
Step 1: Measure and Plan Baseboard Layout
- 0:21–0:35 Plan Room Layout and Measure Walls
- 0:00–0:24 Measure Wall and Plan Baseboard Layout
- 0:49–2:35 Prepare the Room and Measure Baseboard Lengths
Step 2: Acquire Baseboard Material
Step 3: Prepare the Wall Surface
- 0:16–0:29 Prepare Wall and Floor
- 1:43–2:45 Prepare Wall Surface by Removing Residue
- 0:13–0:18 Test Fit and Refine Cuts
Step 4: Make Initial Straight Cuts
- 0:18–0:22 Measure and Cut Trim
- 0:12–0:14 Make the Horizontal and Second Vertical Cuts
- 0:08–0:11 Extend Marks and Make First Cut
Step 5: Cut Inside and Outside Corners
- 1:33–1:49 Miter Cut for Second Outside Corner Piece
- 0:12–0:19 Cut Miter Joints for Outside Corner
- 0:11–0:25 Perform the 45-Degree Miter Cuts
Step 6: Dry Fit and Adjust Cuts
- 1:03–1:15 Dry Fit Baseboards Around Room
- 0:18–0:24 Test Fit and Adjust
- 0:19–0:25 Final Dry-Fit and Installation
Step 7: Install the Baseboard Molding
- 8:34–9:59 Install Baseboard
- 0:16–0:22 Mark Stud Locations and Install Baseboard
- 0:08–0:14 Install Baseboards to the Wall (this video)
Step 8: Fill Nail Holes and Caulk Gaps
- 1:31–1:41 Fill Nail Holes and Caulk Seams
- 22:02–25:10 Finish Baseboards (Fill, Caulk, Paint)
- 0:00–0:04 Fill Nail Holes with Wood Putty
Step 9: Paint or Finish Baseboard
- 22:02–25:10 Finish Baseboards (Fill, Caulk, Paint)
- 1:41–1:52 Apply Final Touch-Up Paint
- 9:00–9:16 Touch-Up Paint Filled Areas
How to Install Baseboard Along a Staircase Wall
A high-level outline for installing baseboard molding along a staircase wall, including planning, cutting, fitting, and finishing steps.
Read the full guide Browse all guides
Planning this project? Shop Oak Valley Designs.

