Measure Wall and Plan Baseboard Layout
From How to Install Baseboard Along a Staircase Wall · Step 1 of 9 · Video by Think Reno

Showing 0:00–0:24 of the source video. Watch the full video with every moment.
What happens in this clip
Begin by measuring the length of the wall where the baseboard will be installed using a measuring tape. Note that if the wall section is longer than a single piece of baseboard material, you will need to create a joint. The video demonstrates a wall length of 146 inches (12 feet 2 inches), requiring a joint as the available baseboard pieces are 8 feet long.
Goal: Determine the required length of baseboard and plan for joints if necessary
What's used
Tools
- Measuring Tape Stanley
- Yard stick
About the full video
This project demonstrates the process of installing baseboard along a wall, specifically focusing on how to create a clean and seamless scarf joint when the wall length exceeds the available baseboard material. It covers measuring, making precise miter cuts, applying wood glue for strength, securing the baseboard with a nail gun, and finishing the joint and edges with caulk and spackle for a professional look.
Step 1 of 9: Measure and Plan Baseboard Layout
Carefully measure the entire length of the staircase wall where the baseboard will be installed. Use a tape measure to get precise measurements for each section of the wall. Note down the measurements for straight runs, as well as any angles or turns. Consider how you will handle inside and outside corners. This planning phase is crucial for determining the total amount of baseboard material needed and for anticipating any complex cuts.
Every video in How to Install Baseboard Along a Staircase Wall
Step 1: Measure and Plan Baseboard Layout
- 0:21–0:35 Plan Room Layout and Measure Walls
- 0:00–0:24 Measure Wall and Plan Baseboard Layout (this video)
- 0:49–2:35 Prepare the Room and Measure Baseboard Lengths
Step 2: Acquire Baseboard Material
Step 3: Prepare the Wall Surface
- 0:16–0:29 Prepare Wall and Floor
- 1:43–2:45 Prepare Wall Surface by Removing Residue
- 0:13–0:18 Test Fit and Refine Cuts
Step 4: Make Initial Straight Cuts
- 0:18–0:22 Measure and Cut Trim
- 0:12–0:14 Make the Horizontal and Second Vertical Cuts
- 0:08–0:11 Extend Marks and Make First Cut
Step 5: Cut Inside and Outside Corners
- 1:33–1:49 Miter Cut for Second Outside Corner Piece
- 0:12–0:19 Cut Miter Joints for Outside Corner
- 0:11–0:25 Perform the 45-Degree Miter Cuts
Step 6: Dry Fit and Adjust Cuts
- 1:03–1:15 Dry Fit Baseboards Around Room
- 0:18–0:24 Test Fit and Adjust
- 0:19–0:25 Final Dry-Fit and Installation
Step 7: Install the Baseboard Molding
- 8:34–9:59 Install Baseboard
- 0:16–0:22 Mark Stud Locations and Install Baseboard
- 0:08–0:14 Install Baseboards to the Wall
Step 8: Fill Nail Holes and Caulk Gaps
- 1:31–1:41 Fill Nail Holes and Caulk Seams
- 22:02–25:10 Finish Baseboards (Fill, Caulk, Paint)
- 0:00–0:04 Fill Nail Holes with Wood Putty
Step 9: Paint or Finish Baseboard
- 22:02–25:10 Finish Baseboards (Fill, Caulk, Paint)
- 1:41–1:52 Apply Final Touch-Up Paint
- 9:00–9:16 Touch-Up Paint Filled Areas
How to Install Baseboard Along a Staircase Wall
A high-level outline for installing baseboard molding along a staircase wall, including planning, cutting, fitting, and finishing steps.
Read the full guide Browse all guides
Planning this project? Shop Oak Valley Designs.

