Apply and Texture Concrete Resurfacer
From How to Resurface Worn Concrete Steps · Step 4 of 6 · Video by Today's Homeowner with Danny Lipford

Showing 2:22–3:19 of the source video. Watch the full video with every moment.
What happens in this clip
Begin applying the mixed concrete resurfacer to the stairs. For horizontal surfaces, pour a manageable amount of resurfacer directly onto the concrete. Use a wooden float to spread the material thinly and evenly across the surface. For vertical surfaces (risers and stair edges), apply the thicker resurfacer using a masonry brush to ensure adhesion and proper coverage. While the resurfacer is still wet, use the masonry brush to create a consistent, textured finish on both horizontal and vertical surfaces. This texture not only enhances the appearance but also increases traction, making the stairs safer to walk on, especially when wet. Work systematically from the top step downwards.
Goal: Create a uniform, textured, and safer new surface on the stairs.
What's used
Tools
- Masonry Brush
- Texturing roller (for specific patterns)
- Wooden Float
- Rubber squeegee (for thinner applications)
- Work Gloves
Materials
- Mixed Concrete Resurfacer QUIKRETE
About the full video
This DIY project demonstrates how to repair damaged concrete stairs by patching chips and cracks with a quick-setting cement mix, then applying a concrete resurfacer to create a uniform, refreshed, and safer walking surface. The process involves preparing the old concrete, mixing and applying repair materials, and finally resurfacing all exposed concrete areas for a cohesive new look.
Step 4 of 6: Mix and Apply Concrete Resurfacer
In a clean mixing bucket, combine the concrete resurfacer powder with the recommended amount of clean water. Mix thoroughly with a drill equipped with a mixing paddle until a lump-free, workable consistency is achieved. The mixture should be like thick pancake batter. Immediately after mixing, pour the resurfacer onto the primed step and spread it evenly using a squeegee or trowel. Work from the top step downwards. Ensure consistent thickness across all surfaces.
Every video in How to Resurface Worn Concrete Steps
Step 1: Inspect and Clean Concrete Steps
- 0:35–0:58 Clean and Prepare Damaged Steps
- 0:13–0:35 Clean Concrete Stairs
- 1:19–2:05 Cleaning the Concrete Surface
Step 2: Repair Cracks and Damage
- 1:07–1:26 Fill Concrete Cracks
- 2:52–3:20 Apply and Level Patching Compound
- 0:00–0:10 Apply Crack Filler
Step 3: Prime the Surface
- 4:24–5:41 Prime the Concrete Surface
- 0:04–0:09 Prepare and Prime the Concrete Surface
- 4:17–5:40 Apply Concrete Bonding Adhesive
Step 4: Mix and Apply Concrete Resurfacer
- 0:13–0:21 Mix Concrete Resurfacing Product
- 2:22–3:19 Apply and Texture Concrete Resurfacer (this video)
- 0:21–0:39 Apply Thin Layer of Resurfacer
Step 5: Texture and Finish
- 16:32–16:40 Achieve Desired Finish
- 0:40–0:45 Apply Broom Finish (Optional)
- 1:16–1:25 Apply Textured Finish
Step 6: Cure the Resurfacer
- 0:33–0:40 Cure Resurfaced Concrete
- 0:12–0:15 Cure and Inspect
- 0:54–1:02 Cure Resurfaced Steps
How to Resurface Worn Concrete Steps
This project outlines the steps to resurface worn concrete steps, including cleaning, repairing cracks, applying a bonding agent, and finishing with a concrete resurfacer product.
Read the full guide Browse all guides
Planning this project? Shop Oak Valley Designs.

