Install Concrete Anchors
From How to Install a Handrail on Outdoor Concrete Steps · Step 3 of 7 · Video by Mikey Pipes - Pipe Doctor Plumbing & Heating & Air

Watch the full video with every moment.
What happens in this clip
Different concrete anchors have different installation methods. For **wedge anchors**, insert them into the hole, thread a nut and washer onto the end, and then tighten the nut; this pulls the wedge up, expanding the anchor. For **drop-in anchors**, fully insert the anchor into the hole, then use a setting tool (often provided by the manufacturer) and a hammer to strike the internal cone, expanding the anchor within the concrete. For **sleeve anchors**, insert the anchor assembly, then tighten the nut, which expands the sleeve against the sides of the hole. Ensure each anchor is fully set and secure before proceeding, as per the manufacturer's instructions. The specific anchor type (e.g., wedge anchor, drop-in anchor, sleeve anchor, concrete screw like Tapcon) should be chosen based on load requirements and concrete conditions.
Goal: Insert the chosen concrete anchors into the cleaned holes and set them according to their specific type (e.g., hammering for wedge anchors, setting tool for drop-in anchors).
What's used
Tools
- Concrete Anchors
- Hammer
- Setting Tool
- Wrench
About the full video
This video briefly shows an existing copper pipe installation, including a circulator pump and various valves and gauges. The objective is stated to be securing the pipe system using split ring hangers, implying that the pipework, which is currently suspended or loosely supported, needs to be permanently fixed to a concrete surface. While the video does not explicitly show the hanger mounting process onto concrete, the provided context dictates a detailed explanation of how such an installation would typically be performed using concrete anchors to create a stable and reliable support system.
Step 3 of 7: Install Concrete Anchors
Insert the concrete anchors into the pilot holes. For wedge anchors, thread the nut onto the bolt a few turns, then tap the anchor into the hole with a hammer until the flange is flush with the concrete surface. For sleeve anchors, insert the anchor until the collar is flush. Tighten the nut to expand the anchor within the concrete. For lag shields, insert the shield and then drive the lag screw into it. Ensure each anchor is firmly seated and ready to support the post.
Every video in How to Install a Handrail on Outdoor Concrete Steps
Step 1: Determine Handrail Placement and Height
Step 2: Drill Pilot Holes for Post Anchors
- 0:31–0:38 Drill Holes for Anchors
- 0:00–0:02 Drill Anchor Hole in Concrete
- 0:29–1:13 Drill Anchor Holes
Step 3: Install Concrete Anchors
- 3:24–4:36 Install Wedge Anchors
- 0:13–0:18 Position Anchor and Insert Wedge Anchor Bolt
- 0:21 Install Concrete Anchors (this video)
Step 4: Attach Handrail Posts to Anchors
- 0:42–0:52 Secure Post Bracket
- 1:16–1:33 Final Mounting and Securing the Handrail
- 0:45–0:51 Install Handrail Posts
Step 5: Measure and Cut Handrail Section
- 0:24–0:39 Measure and Cut Rails
- 0:00–0:43 Measure and Cut Handrail
- 2:44–3:05 Cut and Fit Handrail
Step 6: Attach Handrail to Posts
- 2:11–2:39 Secure Handrail to End Brackets
- 7:17–9:36 Install Handrail and Brackets
- 2:28–2:44 Install Brackets and Mount Handrail
Step 7: Install End Caps or Returns (if applicable)
- 12:04–13:20 Install Handrail Cap and Final Brackets
- 7:35–7:53 Finish with End Caps and Sticker Removal
- 3:21–3:35 Attach Mitered Returns
How to Install a Handrail on Outdoor Concrete Steps
Install a handrail on outdoor concrete steps to improve safety and accessibility. This involves selecting appropriate materials, securely mounting the handrail posts to the concrete, and attaching the handrail itself.
Read the full guide Browse all guides
Planning this project? Shop Oak Valley Designs.

