Uncoiling and Initial Cable Threading
From How to Tension and Adjust Stair Cable Railing · Step 1 of 8 · Video by drdecks

Showing 0:10–0:20 of the source video. Watch the full video with every moment.
What happens in this clip
The workers begin by uncoiling a large spool of stainless steel cable. Once uncoiled and straightened, the cable is carefully threaded through the pre-drilled holes in the railing posts. This process often starts at one end of a cable run, pulling the cable through several intermediate posts to ensure it runs smoothly and without kinks. It is advisable to wear work gloves to protect hands from potential cuts from the cable strands.
Goal: Prepare and thread stainless steel cables through the railing posts.
What's used
Tools
- Work Gloves
- Cut-resistant gloves
Materials
- Stainless Steel Cable
About the full video
This project provides a detailed overview of installing a modern cable railing system on a deck. It covers the essential steps from uncoiling the stainless steel cables, threading them through pre-installed posts, attaching fixed and tensioning terminals, and finally adjusting the cable tension for a secure and visually appealing railing.
Step 1 of 8: Initial Cable Engagement
Begin by carefully threading the stainless steel cable through the designated holes or channels in the starting post. Ensure the cable runs smoothly without kinks or sharp bends. Continue guiding the cable through each subsequent intermediate post, maintaining a consistent path along the staircase. Leave approximately 6-12 inches of extra cable at both the starting and ending posts to facilitate tensioning and secure attachment. This initial slack is crucial for making adjustments later.
Every video in How to Tension and Adjust Stair Cable Railing
Step 1: Initial Cable Engagement
- 0:06–0:26 Thread and Cut Cables
- 3:19–4:10 Thread Cable Railing
- 0:10–0:20 Uncoiling and Initial Cable Threading (this video)
Step 2: Attach Tensioning Fitting to First Cable End
- 8:20–9:15 Swage Cable onto Fittings
- 5:01–6:53 Thread and Terminate Tensioning Cable Ends
- 0:26–0:41 Secure and Tension Cables
Step 3: Install Tensioning Device at Opposite End
- 0:53–0:59 Install Tensioning Terminal
- 0:25–0:35 Attaching and Initial Tightening of Tensioning Terminals
- 8:35–9:31 Tighten Cable Tensioners
Step 4: Initial Cable Tensioning
- 1:06–1:30 Tension Cables
- 1:00–1:09 Hand-Tighten and Seat Cables
- 9:02–11:37 Tension the Cables
Step 5: Check for Sag and Vibration
- 0:29–0:46 Tension the Cables
- 1:06–1:30 Tension Cables
- 1:00–1:09 Hand-Tighten and Seat Cables
Step 6: Fine-Tuning Tension
- 0:29–0:46 Tension the Cables
- 12:30–13:00 Tension Cable Lines
- 1:09–1:18 Final Cable Tensioning
Step 7: Secure Tensioning Device
- 12:30–13:00 Tension Cable Lines
- 6:42–7:06 Final Cable Tensioning
- 1:06–1:30 Tension Cables
Step 8: Final Inspection and Trim Excess Cable
- 10:36–10:55 Trim Excess Cable & Install End Caps
- 1:30–1:40 Final Inspection and Completion
- 1:09–1:18 Final Cable Tensioning
How to Tension and Adjust Stair Cable Railing
This project outlines the steps to properly tension and adjust a cable railing system on a staircase, ensuring safety and a clean aesthetic.
Read the full guide Browse all guides
Planning this project? Shop Oak Valley Designs.

