Tension the Cables
From How to Tension and Adjust Stair Cable Railing · Step 5 of 8 · Video by MyFixitUpLife home improvement pros Mark & Theresa

Showing 0:29–0:46 of the source video. Watch the full video with every moment.
What happens in this clip
After the cables are threaded, proceed to tension them. Use locking pliers to firmly grasp the cable near the tensioner to prevent it from slipping. Then, use an adjustable wrench to turn the tensioning nut on the hardware, slowly tightening the cable until it is taut. In the video, a small piece of wood is placed between the locking pliers and the post to protect the wood from damage during the tensioning process. Repeat for each cable until the desired tension is achieved. Ensure all cables are evenly tensioned to maintain a uniform look and structural integrity.
Goal: Achieve appropriate tension on all installed cables
What's used
Tools
- Adjustable Wrench
- Socket wrench set
- Cable Railing Hardware
- Locking Pliers
- Small Piece of Wood
- Thick cloth
- Stainless Steel Cables
About the full video
This project guides through the installation of a cable railing system on a wooden deck. It involves securing specialized hardware to wooden posts, meticulously threading stainless steel cables through these fittings, applying appropriate tension to each cable to ensure a secure and taut barrier, and finally trimming any excess cable for a professional and clean finish. The process enhances the deck's aesthetic with a modern, open feel while providing a safe perimeter.
Step 5 of 8: Check for Sag and Vibration
Once initial tension is applied, gently push or pluck the cable at its midpoint. A properly tensioned cable should have minimal sag and a high-pitched 'ping' when plucked, indicating it is firm. If there is significant sagging or a dull thud, additional tension is required. Conversely, if the cable feels extremely rigid and seems to be pulling excessively on the posts, it may be over-tensioned.
Every video in How to Tension and Adjust Stair Cable Railing
Step 1: Initial Cable Engagement
- 0:06–0:26 Thread and Cut Cables
- 3:19–4:10 Thread Cable Railing
- 0:10–0:20 Uncoiling and Initial Cable Threading
Step 2: Attach Tensioning Fitting to First Cable End
- 8:20–9:15 Swage Cable onto Fittings
- 5:01–6:53 Thread and Terminate Tensioning Cable Ends
- 0:26–0:41 Secure and Tension Cables
Step 3: Install Tensioning Device at Opposite End
- 0:53–0:59 Install Tensioning Terminal
- 0:25–0:35 Attaching and Initial Tightening of Tensioning Terminals
- 8:35–9:31 Tighten Cable Tensioners
Step 4: Initial Cable Tensioning
- 1:06–1:30 Tension Cables
- 1:00–1:09 Hand-Tighten and Seat Cables
- 9:02–11:37 Tension the Cables
Step 5: Check for Sag and Vibration
- 0:29–0:46 Tension the Cables (this video)
- 1:06–1:30 Tension Cables
- 1:00–1:09 Hand-Tighten and Seat Cables
Step 6: Fine-Tuning Tension
- 0:29–0:46 Tension the Cables
- 12:30–13:00 Tension Cable Lines
- 1:09–1:18 Final Cable Tensioning
Step 7: Secure Tensioning Device
- 12:30–13:00 Tension Cable Lines
- 6:42–7:06 Final Cable Tensioning
- 1:06–1:30 Tension Cables
Step 8: Final Inspection and Trim Excess Cable
- 10:36–10:55 Trim Excess Cable & Install End Caps
- 1:30–1:40 Final Inspection and Completion
- 1:09–1:18 Final Cable Tensioning
How to Tension and Adjust Stair Cable Railing
This project outlines the steps to properly tension and adjust a cable railing system on a staircase, ensuring safety and a clean aesthetic.
Read the full guide Browse all guides
Planning this project? Shop Oak Valley Designs.

