Tension the Cables
From How to Tension and Adjust Stair Cable Railing · Step 4 of 8 · Video by drdecks

Showing 9:02–11:37 of the source video. Watch the full video with every moment.
What happens in this clip
Now that all cables are pretensioned, use a duckbill vice grip (or a specialized cable tensioning tool if available) to hold the cable securely, and a socket wrench with the correct bit to tighten the threaded fittings. Tighten each cable until it is taut. You may hear rattling from stiffeners inside the posts, which will subside as tension increases. It's important to tighten by feel and sound, ensuring the cable is tight enough so a child cannot easily pass through, but not overly tight. As you tension middle cables, the top and bottom ones might loosen slightly, so re-check and adjust as needed.
Goal: Achieve optimal tightness and safety for the cable railing.
What's used
Tools
- Duckbill Vice Grip
- Pliers with protective padding
- Railing Posts American Structures
- Socket Bit (Correct Size)
- Socket Wrench
About the full video
This project provides detailed instructions on installing a cable railing system, specifically focusing on fitting the top cap, threading the stainless steel cables, applying anti-seize lubricant, adding washers, and tensioning the cables using specialized tools. It also briefly covers the installation of composite decking on a dock and an upper deck, showcasing how the cable railing system integrates with these structures.
Step 4 of 8: Initial Cable Tensioning
Using the installed tensioning device (turnbuckle or nuts on the threaded rod), begin to apply tension to the cable. Gradually tighten the device, observing the cable's tautness. The goal is to remove significant slack, making the cable firm to the touch without causing excessive deflection or stress on the posts. Aim for a slight give when pressed, indicating adequate tension without over-tightening.
Every video in How to Tension and Adjust Stair Cable Railing
Step 1: Initial Cable Engagement
- 0:06–0:26 Thread and Cut Cables
- 3:19–4:10 Thread Cable Railing
- 0:10–0:20 Uncoiling and Initial Cable Threading
Step 2: Attach Tensioning Fitting to First Cable End
- 8:20–9:15 Swage Cable onto Fittings
- 5:01–6:53 Thread and Terminate Tensioning Cable Ends
- 0:26–0:41 Secure and Tension Cables
Step 3: Install Tensioning Device at Opposite End
- 0:53–0:59 Install Tensioning Terminal
- 0:25–0:35 Attaching and Initial Tightening of Tensioning Terminals
- 8:35–9:31 Tighten Cable Tensioners
Step 4: Initial Cable Tensioning
- 1:06–1:30 Tension Cables
- 1:00–1:09 Hand-Tighten and Seat Cables
- 9:02–11:37 Tension the Cables (this video)
Step 5: Check for Sag and Vibration
- 0:29–0:46 Tension the Cables
- 1:06–1:30 Tension Cables
- 1:00–1:09 Hand-Tighten and Seat Cables
Step 6: Fine-Tuning Tension
- 0:29–0:46 Tension the Cables
- 12:30–13:00 Tension Cable Lines
- 1:09–1:18 Final Cable Tensioning
Step 7: Secure Tensioning Device
- 12:30–13:00 Tension Cable Lines
- 6:42–7:06 Final Cable Tensioning
- 1:06–1:30 Tension Cables
Step 8: Final Inspection and Trim Excess Cable
- 10:36–10:55 Trim Excess Cable & Install End Caps
- 1:30–1:40 Final Inspection and Completion
- 1:09–1:18 Final Cable Tensioning
How to Tension and Adjust Stair Cable Railing
This project outlines the steps to properly tension and adjust a cable railing system on a staircase, ensuring safety and a clean aesthetic.
Read the full guide Browse all guides
Planning this project? Shop Oak Valley Designs.

