Tension Cables
From How to Tension and Adjust Stair Cable Railing · Step 7 of 8 · Video by Premier Outdoor Living

Showing 1:06–1:30 of the source video. Watch the full video with every moment.
What happens in this clip
Once all cables are installed, use a wrench to systematically tighten the nuts on the tensioning terminals. Work your way across all the cables, applying even tension to each one. The goal is to achieve a taut, parallel appearance for all cables, ensuring they are secure and meet safety standards. Avoid over-tightening any single cable, which could warp posts or damage fittings.
Goal: Achieve proper tension in all installed cables
What's used
Tools
- Tension Gauge
- Wrench
- Adjustable wrench
Materials
- Installed Cables Decorators
About the full video
This project details the installation of a cable railing system on a deck, focusing on assembling the cable ends, threading the cables through posts, and tensioning them for a secure and aesthetically pleasing finish. The process involves unpacking the cable railing kit, attaching fixed and tensioning fittings to the cables, running the cables through the pre-drilled posts, and finally, using a crimping tool and wrench to properly secure and tension each cable.
Step 7 of 8: Secure Tensioning Device
Once the desired tension is achieved for each cable, secure the tensioning device to prevent it from backing off due to vibrations or environmental changes. If using a turnbuckle, some models come with locking nuts or mechanisms. For threaded rods, ensure the nuts are tightened firmly against the post or any locking washer. Consider using thread-locking compound for added security, especially in outdoor or high-vibration environments.
Every video in How to Tension and Adjust Stair Cable Railing
Step 1: Initial Cable Engagement
- 0:06–0:26 Thread and Cut Cables
- 3:19–4:10 Thread Cable Railing
- 0:10–0:20 Uncoiling and Initial Cable Threading
Step 2: Attach Tensioning Fitting to First Cable End
- 8:20–9:15 Swage Cable onto Fittings
- 5:01–6:53 Thread and Terminate Tensioning Cable Ends
- 0:26–0:41 Secure and Tension Cables
Step 3: Install Tensioning Device at Opposite End
- 0:53–0:59 Install Tensioning Terminal
- 0:25–0:35 Attaching and Initial Tightening of Tensioning Terminals
- 8:35–9:31 Tighten Cable Tensioners
Step 4: Initial Cable Tensioning
- 1:06–1:30 Tension Cables
- 1:00–1:09 Hand-Tighten and Seat Cables
- 9:02–11:37 Tension the Cables
Step 5: Check for Sag and Vibration
- 0:29–0:46 Tension the Cables
- 1:06–1:30 Tension Cables
- 1:00–1:09 Hand-Tighten and Seat Cables
Step 6: Fine-Tuning Tension
- 0:29–0:46 Tension the Cables
- 12:30–13:00 Tension Cable Lines
- 1:09–1:18 Final Cable Tensioning
Step 7: Secure Tensioning Device
- 12:30–13:00 Tension Cable Lines
- 6:42–7:06 Final Cable Tensioning
- 1:06–1:30 Tension Cables (this video)
Step 8: Final Inspection and Trim Excess Cable
- 10:36–10:55 Trim Excess Cable & Install End Caps
- 1:30–1:40 Final Inspection and Completion
- 1:09–1:18 Final Cable Tensioning
Questions about How to Tension and Adjust Stair Cable Railing
What specialized tools are essential for tensioning cable railings, and why can't I just use standard pliers?
A dedicated cable cutter and swaging tool (like the CityPost CP-CC&SW) is crucial for clean, burr-free cuts and secure, professional-looking swages. Standard pliers won't achieve the necessary grip or precision, which can compromise both the aesthetics and safety of your railing. A plier wrench is also highly recommended for gripping fittings without causing damage during tightening.
What are the most important safety precautions to take when working with cable railing tensioning?
Always wear work gloves to protect your hands from sharp cable ends and burrs, which can cause cuts. Ensure all swaged fittings are properly compressed and secure to prevent cable slippage, a critical safety failure point. Double-check every connection for tightness before applying full tension and after final adjustments to maintain structural integrity.
How do I know if my cable railing is tensioned correctly, and what happens if it's too loose or too tight?
Proper tension means cables are taut with minimal sag, typically allowing about a 1/4-inch deflection when pressed in the middle of a span. Too loose, and the railing won't meet safety codes and will look sloppy; too tight, and you risk putting excessive stress on your posts, potentially causing them to bow. Aim for uniform tension across all cables for the best aesthetic and structural performance.
Is this cable railing tensioning project truly beginner-friendly, and how accurate is the 4-hour time estimate for a first-timer?
While classified as beginner, this project requires patience and attention to detail, especially during swaging and initial tensioning. The 4-hour estimate is achievable if you have all tools and materials organized and follow instructions carefully. First-timers might take a bit longer to get comfortable with the process, so budgeting an extra hour or two is wise.
I've tensioned my cables, but some still seem to sag more than others. How can I troubleshoot this?
First, ensure all tensioning devices (like turnbuckles) are adjusted evenly, making small, incremental turns. If sag persists, check for any improperly swaged fittings that might be slipping or if the cable length was cut slightly too long for that specific run. You might need to re-swage or adjust the cable length for the problematic section.
After initial tensioning, will I need to re-tension the cables over time?
Yes, it's a good practice to periodically check your cable railing tension, especially after the first few weeks as components settle, and then every 6-12 months. Environmental factors like temperature and humidity can cause wood posts to expand or contract, affecting cable tautness. A quick visual inspection and gentle tug on each cable will help you identify if any adjustments are needed.
What are the main material costs for this project, and are there cheaper alternatives to stainless steel cable?
The primary material costs are for the stainless steel cable, tensioning fittings, and turnbuckles, chosen for their durability and corrosion resistance. While cheaper galvanized steel options exist, they are not recommended for outdoor or high-humidity environments due to faster corrosion and a shorter lifespan. Investing in marine-grade stainless steel (like 316) ensures longevity and minimizes future maintenance, offering better long-term value.
How to Tension and Adjust Stair Cable Railing
This project outlines the steps to properly tension and adjust a cable railing system on a staircase, ensuring safety and a clean aesthetic.
Read the full guide Browse all guides
Planning this project? Shop Oak Valley Designs.

