Final Inspection and Completion
From How to Tension and Adjust Stair Cable Railing · Step 8 of 8 · Video by Premier Outdoor Living

Showing 1:30–1:40 of the source video. Watch the full video with every moment.
What happens in this clip
After tensioning all the cables, perform a final visual inspection of the entire cable railing system. Check for any loose connections, kinks in the cables, or uneven tension. Ensure all nuts are securely fastened and that the railing meets aesthetic expectations and safety requirements. The goal is a clean, modern, and sturdy railing that enhances the deck's appearance.
Goal: Verify the proper installation and functionality of the cable railing
What's used
Materials
- Completed Cable Railing
About the full video
This project details the installation of a cable railing system on a deck, focusing on assembling the cable ends, threading the cables through posts, and tensioning them for a secure and aesthetically pleasing finish. The process involves unpacking the cable railing kit, attaching fixed and tensioning fittings to the cables, running the cables through the pre-drilled posts, and finally, using a crimping tool and wrench to properly secure and tension each cable.
Step 8 of 8: Final Inspection and Trim Excess Cable
Walk the length of the cable railing system, visually inspecting each cable, fitting, and tensioning device for proper installation, alignment, and security. Ensure there are no frayed ends or sharp protrusions. Once satisfied with the tension and security, use a cable cutter to trim any excess cable extending beyond the tensioning fitting at the starting post. Leave a small amount of cable, typically 1/2 to 1 inch, beyond the fitting for aesthetic reasons or future adjustments.
Every video in How to Tension and Adjust Stair Cable Railing
Step 1: Initial Cable Engagement
- 0:06–0:26 Thread and Cut Cables
- 3:19–4:10 Thread Cable Railing
- 0:10–0:20 Uncoiling and Initial Cable Threading
Step 2: Attach Tensioning Fitting to First Cable End
- 8:20–9:15 Swage Cable onto Fittings
- 5:01–6:53 Thread and Terminate Tensioning Cable Ends
- 0:26–0:41 Secure and Tension Cables
Step 3: Install Tensioning Device at Opposite End
- 0:53–0:59 Install Tensioning Terminal
- 0:25–0:35 Attaching and Initial Tightening of Tensioning Terminals
- 8:35–9:31 Tighten Cable Tensioners
Step 4: Initial Cable Tensioning
- 1:06–1:30 Tension Cables
- 1:00–1:09 Hand-Tighten and Seat Cables
- 9:02–11:37 Tension the Cables
Step 5: Check for Sag and Vibration
- 0:29–0:46 Tension the Cables
- 1:06–1:30 Tension Cables
- 1:00–1:09 Hand-Tighten and Seat Cables
Step 6: Fine-Tuning Tension
- 0:29–0:46 Tension the Cables
- 12:30–13:00 Tension Cable Lines
- 1:09–1:18 Final Cable Tensioning
Step 7: Secure Tensioning Device
- 12:30–13:00 Tension Cable Lines
- 6:42–7:06 Final Cable Tensioning
- 1:06–1:30 Tension Cables
Step 8: Final Inspection and Trim Excess Cable
- 10:36–10:55 Trim Excess Cable & Install End Caps
- 1:30–1:40 Final Inspection and Completion (this video)
- 1:09–1:18 Final Cable Tensioning
How to Tension and Adjust Stair Cable Railing
This project outlines the steps to properly tension and adjust a cable railing system on a staircase, ensuring safety and a clean aesthetic.
Read the full guide Browse all guides
Planning this project? Shop Oak Valley Designs.

