Tension Cables
From How to Tension and Adjust Stair Cable Railing · Step 4 of 8 · Video by Premier Outdoor Living

Showing 1:06–1:30 of the source video. Watch the full video with every moment.
What happens in this clip
Once all cables are installed, use a wrench to systematically tighten the nuts on the tensioning terminals. Work your way across all the cables, applying even tension to each one. The goal is to achieve a taut, parallel appearance for all cables, ensuring they are secure and meet safety standards. Avoid over-tightening any single cable, which could warp posts or damage fittings.
Goal: Achieve proper tension in all installed cables
What's used
Tools
- Tension Gauge
- Wrench
- Adjustable wrench
Materials
- Installed Cables Decorators
About the full video
This project details the installation of a cable railing system on a deck, focusing on assembling the cable ends, threading the cables through posts, and tensioning them for a secure and aesthetically pleasing finish. The process involves unpacking the cable railing kit, attaching fixed and tensioning fittings to the cables, running the cables through the pre-drilled posts, and finally, using a crimping tool and wrench to properly secure and tension each cable.
Step 4 of 8: Initial Cable Tensioning
Using the installed tensioning device (turnbuckle or nuts on the threaded rod), begin to apply tension to the cable. Gradually tighten the device, observing the cable's tautness. The goal is to remove significant slack, making the cable firm to the touch without causing excessive deflection or stress on the posts. Aim for a slight give when pressed, indicating adequate tension without over-tightening.
Every video in How to Tension and Adjust Stair Cable Railing
Step 1: Initial Cable Engagement
- 0:06–0:26 Thread and Cut Cables
- 3:19–4:10 Thread Cable Railing
- 0:10–0:20 Uncoiling and Initial Cable Threading
Step 2: Attach Tensioning Fitting to First Cable End
- 8:20–9:15 Swage Cable onto Fittings
- 5:01–6:53 Thread and Terminate Tensioning Cable Ends
- 0:26–0:41 Secure and Tension Cables
Step 3: Install Tensioning Device at Opposite End
- 0:53–0:59 Install Tensioning Terminal
- 0:25–0:35 Attaching and Initial Tightening of Tensioning Terminals
- 8:35–9:31 Tighten Cable Tensioners
Step 4: Initial Cable Tensioning
- 1:06–1:30 Tension Cables (this video)
- 1:00–1:09 Hand-Tighten and Seat Cables
- 9:02–11:37 Tension the Cables
Step 5: Check for Sag and Vibration
- 0:29–0:46 Tension the Cables
- 1:06–1:30 Tension Cables
- 1:00–1:09 Hand-Tighten and Seat Cables
Step 6: Fine-Tuning Tension
- 0:29–0:46 Tension the Cables
- 12:30–13:00 Tension Cable Lines
- 1:09–1:18 Final Cable Tensioning
Step 7: Secure Tensioning Device
- 12:30–13:00 Tension Cable Lines
- 6:42–7:06 Final Cable Tensioning
- 1:06–1:30 Tension Cables
Step 8: Final Inspection and Trim Excess Cable
- 10:36–10:55 Trim Excess Cable & Install End Caps
- 1:30–1:40 Final Inspection and Completion
- 1:09–1:18 Final Cable Tensioning
How to Tension and Adjust Stair Cable Railing
This project outlines the steps to properly tension and adjust a cable railing system on a staircase, ensuring safety and a clean aesthetic.
Read the full guide Browse all guides
Planning this project? Shop Oak Valley Designs.

