Tension Cable Lines
From How to Tension and Adjust Stair Cable Railing · Step 6 of 8 · Video by Premier Outdoor Living

Showing 12:30–13:00 of the source video. Watch the full video with every moment.
What happens in this clip
Once all cable lines are threaded and fixed at one end, begin the tensioning process. Using a ratcheting wrench and an Allen key (Cobalt brand shown) on the tensioning hardware located on the exterior of the posts, tighten each cable. Work incrementally, tightening all cables evenly to avoid over-stressing any single line or distorting the posts. Continuously check the tension and ensure that the cables are taut and straight. The goal is to achieve a tight, secure railing system that has minimal deflection and meets local building codes for safety (typically less than 4-inch spacing between cables).
Goal: This final step involves tightening the cable lines to the correct tension using a specialized wrench, ensuring the railing is taut, secure, and meets safety standards.
What's used
Tools
- Allen Key (Cobalt brand shown) Cobalt
- Cable Railing System (Installed)
- Ratcheting Wrench
About the full video
This video details the process of installing a modern cable railing system on a deck, specifically focusing on the preparation and installation of posts, the insertion and tensioning of the cable lines, and ensuring the system adheres to safety codes for both horizontal and angled stair sections. The project highlights the importance of proper blocking and the use of specialized tools for a sleek, contemporary aesthetic.
Step 6 of 8: Fine-Tuning Tension
Based on the sag and vibration checks, make small, incremental adjustments to the tensioning devices. Tighten or loosen as needed to achieve a consistent and appropriate level of tautness across all cables in the system. Aim for a tension that provides a solid feel without causing undue stress on the posts. Refer to manufacturer recommendations or local building codes for specific tensioning guidelines if available.
Every video in How to Tension and Adjust Stair Cable Railing
Step 1: Initial Cable Engagement
- 0:06–0:26 Thread and Cut Cables
- 3:19–4:10 Thread Cable Railing
- 0:10–0:20 Uncoiling and Initial Cable Threading
Step 2: Attach Tensioning Fitting to First Cable End
- 8:20–9:15 Swage Cable onto Fittings
- 5:01–6:53 Thread and Terminate Tensioning Cable Ends
- 0:26–0:41 Secure and Tension Cables
Step 3: Install Tensioning Device at Opposite End
- 0:53–0:59 Install Tensioning Terminal
- 0:25–0:35 Attaching and Initial Tightening of Tensioning Terminals
- 8:35–9:31 Tighten Cable Tensioners
Step 4: Initial Cable Tensioning
- 1:06–1:30 Tension Cables
- 1:00–1:09 Hand-Tighten and Seat Cables
- 9:02–11:37 Tension the Cables
Step 5: Check for Sag and Vibration
- 0:29–0:46 Tension the Cables
- 1:06–1:30 Tension Cables
- 1:00–1:09 Hand-Tighten and Seat Cables
Step 6: Fine-Tuning Tension
- 0:29–0:46 Tension the Cables
- 12:30–13:00 Tension Cable Lines (this video)
- 1:09–1:18 Final Cable Tensioning
Step 7: Secure Tensioning Device
- 12:30–13:00 Tension Cable Lines
- 6:42–7:06 Final Cable Tensioning
- 1:06–1:30 Tension Cables
Step 8: Final Inspection and Trim Excess Cable
- 10:36–10:55 Trim Excess Cable & Install End Caps
- 1:30–1:40 Final Inspection and Completion
- 1:09–1:18 Final Cable Tensioning
How to Tension and Adjust Stair Cable Railing
This project outlines the steps to properly tension and adjust a cable railing system on a staircase, ensuring safety and a clean aesthetic.
Read the full guide Browse all guides
Planning this project? Shop Oak Valley Designs.

