Thread and Terminate Tensioning Cable Ends
From How to Tension and Adjust Stair Cable Railing · Step 2 of 8 · Video by mark galicic

Showing 5:01–6:53 of the source video. Watch the full video with every moment.
What happens in this clip
Once one end of a cable is crimped, thread the cable through all the pre-drilled holes in the stainless steel posts. Ensure the cable passes smoothly through each post. Once threaded, take the tensioning swage fitting (a threaded end designed for tensioning) and insert the free end of the cable into it, pushing until it bottoms out. As with the previous step, use the crimping tool to make two crimps, rotating 90 degrees between each, for a secure connection. After crimping, slide a washer onto the threaded portion of the tensioning fitting, followed by a nut. Hand-tighten the nut to hold the cable in place, but do not apply full tension at this stage. Repeat this for all cables.
Goal: After the non-tensioning ends are crimped, thread each cable through the posts and then attach the tensioning swage fitting to the other end, securing it initially with hand-tightened hardware.
What's used
Tools
- Crimping Tool
- Nuts
- Snips
- Stainless Steel Cables
- Tensioning Swage Fittings
- Washers
About the full video
This video provides a step-by-step guide on how to install a modern cable railing system on a deck, emphasizing the preparation of stainless steel posts, the crimping of cable ends, and the initial setup of the tensioning system. The process involves welding custom top rails, attaching swage fittings to pre-cut stainless steel cables, and threading them through the posts, culminating in a sleek and durable railing. The video highlights the importance of hand-tightening before final tensioning, which will occur after the cap rail installation.
What's said in this clip
then okay i'm going to show you the final step here is we're going to terminate these into the threaded end here so once you did this enough you'll get you get on to it uh what i what i found is if you just rest your cutter right along the edge and it's just a just a pair of snips and they come with the roll of cable usually and same thing we're going to make sure that we stick this all the way to the bottom of that same thing with the crimpers i don't know how good my angle is on the camera here but i apologize the same thing about a quarter inch in i like to do is just get a bite on it then when you follow through with it it pretty much keeps it in place we're going to do the same thing we're going to rotate this 90 degrees of the last crimp and it'll just gives it more more rigidity and then we're going to feed this through and just enough to get a washer and a nut on here and we don't want to tension this at this point all you want to do is just you're doing everything hand tight and there we go so we're going to get all the rest of these cables done and i'll show you the procedure for tensioning but we're not going to put full tension on until i'm done putting the cap rail on this and that'll probably be somewhere towards spring so i hope you enjoyed this i'll give you one more shot here when i get the rest of these terminated but uh you can see the the real clean look uh cable rail systems are they're they're still pretty popular um amazon sells all the stuff for it all
Automatically transcribed from the source video.
Step 2 of 8: Attach Tensioning Fitting to First Cable End
At the starting post, take the slackened end of the cable and attach a tensioning fitting. If using a swage fitting, position it onto the cable and use a swaging tool to permanently crimp it in place. If using a threaded terminal, follow the manufacturer's instructions for securing it, which may involve a specific crimping method or adhesive. Ensure the fitting is firmly attached and aligned correctly with the cable's direction.
Every video in How to Tension and Adjust Stair Cable Railing
Step 1: Initial Cable Engagement
- 0:06–0:26 Thread and Cut Cables
- 3:19–4:10 Thread Cable Railing
- 0:10–0:20 Uncoiling and Initial Cable Threading
Step 2: Attach Tensioning Fitting to First Cable End
- 8:20–9:15 Swage Cable onto Fittings
- 5:01–6:53 Thread and Terminate Tensioning Cable Ends (this video)
- 0:26–0:41 Secure and Tension Cables
Step 3: Install Tensioning Device at Opposite End
- 0:53–0:59 Install Tensioning Terminal
- 0:25–0:35 Attaching and Initial Tightening of Tensioning Terminals
- 8:35–9:31 Tighten Cable Tensioners
Step 4: Initial Cable Tensioning
- 1:06–1:30 Tension Cables
- 1:00–1:09 Hand-Tighten and Seat Cables
- 9:02–11:37 Tension the Cables
Step 5: Check for Sag and Vibration
- 0:29–0:46 Tension the Cables
- 1:06–1:30 Tension Cables
- 1:00–1:09 Hand-Tighten and Seat Cables
Step 6: Fine-Tuning Tension
- 0:29–0:46 Tension the Cables
- 12:30–13:00 Tension Cable Lines
- 1:09–1:18 Final Cable Tensioning
Step 7: Secure Tensioning Device
- 12:30–13:00 Tension Cable Lines
- 6:42–7:06 Final Cable Tensioning
- 1:06–1:30 Tension Cables
Step 8: Final Inspection and Trim Excess Cable
- 10:36–10:55 Trim Excess Cable & Install End Caps
- 1:30–1:40 Final Inspection and Completion
- 1:09–1:18 Final Cable Tensioning
How to Tension and Adjust Stair Cable Railing
This project outlines the steps to properly tension and adjust a cable railing system on a staircase, ensuring safety and a clean aesthetic.
Read the full guide Browse all guides
Planning this project? Shop Oak Valley Designs.

