Trim Excess Cable & Install End Caps
From How to Tension and Adjust Stair Cable Railing · Step 8 of 8 · Video by Premier Outdoor Living

Showing 10:36–10:55 of the source video. Watch the full video with every moment.
What happens in this clip
Once all cables are properly tensioned and you have verified their uniformity and tautness, use heavy-duty pliers or specialized cable snips to trim any excess cable wire that extends past the tensioning fittings. The cut should be clean and flush with the fitting or trimmed to a specified length as per the manufacturer's instructions. After trimming, press or screw on the decorative end caps, often referred to as 'buttons', over the exposed tensioning hardware. These caps not only conceal the hardware for a cleaner aesthetic but also provide a smooth, polished, and safe finish to the completed cable railing.
Goal: Cut off any excess cable extending beyond the tensioning hardware and then install protective end caps or buttons for a clean, finished appearance.
What's used
Tools
- End Caps/Buttons Decorator's Cable Rail
- Heavy-Duty Pliers or Cable Snips
- Bolt cutters
About the full video
This video details the installation of a sleek cable railing system on a deck, focusing on securing posts, stringing cables, and precisely tensioning them for a modern look with unobstructed views. It covers the tools and techniques required for each stage, including securing the structural components and finely adjusting the cable tension.
What's said in this clip
down tighten them up be good to go now that we have them all tensioned we can cut off the slack you can see the extra run of cable you want a nice heavy duty set of snippers here i don't know what you call these wire cutters i don't know they're just heavy duty pliers [Music] finish it off with our little button boom toss it
Automatically transcribed from the source video.
Step 8 of 8: Final Inspection and Trim Excess Cable
Walk the length of the cable railing system, visually inspecting each cable, fitting, and tensioning device for proper installation, alignment, and security. Ensure there are no frayed ends or sharp protrusions. Once satisfied with the tension and security, use a cable cutter to trim any excess cable extending beyond the tensioning fitting at the starting post. Leave a small amount of cable, typically 1/2 to 1 inch, beyond the fitting for aesthetic reasons or future adjustments.
Every video in How to Tension and Adjust Stair Cable Railing
Step 1: Initial Cable Engagement
- 0:06–0:26 Thread and Cut Cables
- 3:19–4:10 Thread Cable Railing
- 0:10–0:20 Uncoiling and Initial Cable Threading
Step 2: Attach Tensioning Fitting to First Cable End
- 8:20–9:15 Swage Cable onto Fittings
- 5:01–6:53 Thread and Terminate Tensioning Cable Ends
- 0:26–0:41 Secure and Tension Cables
Step 3: Install Tensioning Device at Opposite End
- 0:53–0:59 Install Tensioning Terminal
- 0:25–0:35 Attaching and Initial Tightening of Tensioning Terminals
- 8:35–9:31 Tighten Cable Tensioners
Step 4: Initial Cable Tensioning
- 1:06–1:30 Tension Cables
- 1:00–1:09 Hand-Tighten and Seat Cables
- 9:02–11:37 Tension the Cables
Step 5: Check for Sag and Vibration
- 0:29–0:46 Tension the Cables
- 1:06–1:30 Tension Cables
- 1:00–1:09 Hand-Tighten and Seat Cables
Step 6: Fine-Tuning Tension
- 0:29–0:46 Tension the Cables
- 12:30–13:00 Tension Cable Lines
- 1:09–1:18 Final Cable Tensioning
Step 7: Secure Tensioning Device
- 12:30–13:00 Tension Cable Lines
- 6:42–7:06 Final Cable Tensioning
- 1:06–1:30 Tension Cables
Step 8: Final Inspection and Trim Excess Cable
- 10:36–10:55 Trim Excess Cable & Install End Caps (this video)
- 1:30–1:40 Final Inspection and Completion
- 1:09–1:18 Final Cable Tensioning
How to Tension and Adjust Stair Cable Railing
This project outlines the steps to properly tension and adjust a cable railing system on a staircase, ensuring safety and a clean aesthetic.
Read the full guide Browse all guides
Planning this project? Shop Oak Valley Designs.

