Trim Excess Carpet and Prepare Final Riser
From How to Install Carpet Treads on Stairs with a Deep Nosing Overhang · Step 3 of 7 · Video by Direct Carpet

Showing 3:53–7:38 of the source video. Watch the full video with every moment.
What happens in this clip
After stapling the second tread, the video demonstrates securing the nosing and then trimming the excess carpet for the third (and final, in this case) stair riser and the top landing. Begin by using a utility knife to cut away the excess carpet and underpad that extends past the top edge of the final riser. Then, use a tape measure and pencil to mark the desired cut line on the carpet underpad for the top riser. You'll mark both sides and use a straight edge to connect them. Carefully cut along these marked lines with a pair of sharp scissors or shears. The binding (the finished edge of the carpet) is never as tall as the pile itself, creating a 'kick' that helps it fit snugly.
Goal: Cut the stair runner to the correct length for the final riser and top landing
What's used
Tools
- Pencil
- Scissors
- Straight Edge
- Metal yardstick
- Tape Measure Stanley
- Utility Knife
About the full video
This project provides step-by-step instructions on how to install a carpet stair runner on a set of three stairs. The process involves precise measuring, securely stapling the runner, tucking and shaping the carpet around the stair nosing, and trimming excess material for a clean, professional finish.
Step 3 of 7: Dry Fit and Trim Carpet Treads
Place each cut carpet tread onto its intended stair to check the fit. Pay close attention to how it sits around the nosing and against the riser. Make any necessary small adjustments or trims to ensure the carpet lies flat and covers the tread area completely without bunching or leaving gaps. The goal is a precise fit that follows the contours of the stair.
Every video in How to Install Carpet Treads on Stairs with a Deep Nosing Overhang
Step 1: Measure Existing Tread Depth and Nosing
- 0:57–1:16 Measure Treads and Mark Laminate
- 0:46–1:05 Measure and Cut Underlayment
- 0:12–0:57 Measure and Cut Carpet Tread
Step 2: Cut Carpet Treads to Size
- 7:20–9:07 Measure and Cut Carpet
- 0:12–0:57 Measure and Cut Carpet Tread
- 2:09–3:19 Measure and Cut Carpet Pieces
Step 3: Dry Fit and Trim Carpet Treads
- 2:13–2:35 Test Fit and Adjust Treads
- 3:53–7:38 Trim Excess Carpet and Prepare Final Riser (this video)
- 0:57–2:36 Pre-form and Secure Carpet Underneath Tread
Step 4: Apply Adhesive to Treads
- 0:05–0:06 Apply Adhesive to Treads
- 0:34–0:46 Apply Carpet Adhesive to Stairs
- 0:16–0:21 Apply Peel-and-Stick Carpet Treads
Step 5: Install Carpet Treads
- 0:04–0:06 Install Carpet Treads
- 0:59–2:07 Install First Stair Tread
- 0:11–0:43 Install Remaining Carpet Stair Treads
Step 6: Secure Nosing Overhang
- 0:57–2:36 Pre-form and Secure Carpet Underneath Tread
- 1:19–1:59 Lay and Secure Carpet Sections (Repetitive)
- 12:05–14:25 Fold and Staple Carpet Over Next Nose
Step 7: Allow Adhesive to Cure
- 3:06–3:19 Project Completion
- 3:44–4:26 Final Curing and Caulking
- 0:31–0:38 Inspect and Finish Installation
How to Install Carpet Treads on Stairs with a Deep Nosing Overhang
This project outlines the steps for installing carpet treads on stairs that have a deep nosing overhang. It covers measuring, cutting, fitting, and securing the treads to ensure a safe and aesthetically pleasing result.
Read the full guide Browse all guides
Planning this project? Shop Oak Valley Designs.

