Measure and Cut Carpet
From How to Install Carpet Treads on Stairs with a Deep Nosing Overhang · Step 2 of 7 · Video by Direct Carpet

Showing 7:20–9:07 of the source video. Watch the full video with every moment.
What happens in this clip
Measure the width of the stair tread from stringer to stringer (e.g., 36 1/8 inches) and the depth from the nose to the back riser (e.g., 13 inches). To allow for trimming and a snug fit, cut the carpet pieces slightly larger than these measurements (e.g., 37 inches wide by 14 inches deep). Use a utility knife and a straight edge to ensure clean, straight cuts. You will need one carpet piece per tread.
What's used
Tools
- Straight Edge
- Tape Measure
- Utility Knife
About the full video
This video provides detailed, step-by-step instructions on how to install carpet on stair treads using various trim tools to achieve a clean, professional finish. It covers preparing the stairs with tack strip and underpad, precise carpet cutting, and techniques for stretching, stapling, and tucking the carpet for a polished look.
Step 2 of 7: Cut Carpet Treads to Size
Using your recorded measurements, cut the carpet material for each tread. The cut piece should match the tread depth and extend to cover the nosing. If your carpet has a backing, ensure you cut through both the carpet pile and the backing cleanly. For a clean edge, you might consider cutting slightly larger and then trimming to fit precisely in the next step.
Every video in How to Install Carpet Treads on Stairs with a Deep Nosing Overhang
Step 1: Measure Existing Tread Depth and Nosing
- 0:57–1:16 Measure Treads and Mark Laminate
- 0:46–1:05 Measure and Cut Underlayment
- 0:12–0:57 Measure and Cut Carpet Tread
Step 2: Cut Carpet Treads to Size
- 7:20–9:07 Measure and Cut Carpet (this video)
- 0:12–0:57 Measure and Cut Carpet Tread
- 2:09–3:19 Measure and Cut Carpet Pieces
Step 3: Dry Fit and Trim Carpet Treads
- 2:13–2:35 Test Fit and Adjust Treads
- 3:53–7:38 Trim Excess Carpet and Prepare Final Riser
- 0:57–2:36 Pre-form and Secure Carpet Underneath Tread
Step 4: Apply Adhesive to Treads
- 0:05–0:06 Apply Adhesive to Treads
- 0:34–0:46 Apply Carpet Adhesive to Stairs
- 0:16–0:21 Apply Peel-and-Stick Carpet Treads
Step 5: Install Carpet Treads
- 0:04–0:06 Install Carpet Treads
- 0:59–2:07 Install First Stair Tread
- 0:11–0:43 Install Remaining Carpet Stair Treads
Step 6: Secure Nosing Overhang
- 0:57–2:36 Pre-form and Secure Carpet Underneath Tread
- 1:19–1:59 Lay and Secure Carpet Sections (Repetitive)
- 12:05–14:25 Fold and Staple Carpet Over Next Nose
Step 7: Allow Adhesive to Cure
- 3:06–3:19 Project Completion
- 3:44–4:26 Final Curing and Caulking
- 0:31–0:38 Inspect and Finish Installation
How to Install Carpet Treads on Stairs with a Deep Nosing Overhang
This project outlines the steps for installing carpet treads on stairs that have a deep nosing overhang. It covers measuring, cutting, fitting, and securing the treads to ensure a safe and aesthetically pleasing result.
Read the full guide Browse all guides
Planning this project? Shop Oak Valley Designs.

