Measure and Cut Carpet Pieces
From How to Install Carpet Treads on Stairs with a Deep Nosing Overhang · Step 2 of 7 · Video by Direct Carpet

Showing 2:09–3:19 of the source video. Watch the full video with every moment.
What happens in this clip
Based on the stair measurements, lay out the carpet and carefully cut it into individual pieces for each tread and riser. It's often recommended to cut the carpet slightly larger than the exact dimensions to allow for adjustments and trimming. Use a metal straight edge to guide a sharp utility knife for precise, straight cuts through the carpet backing. Ensure the carpet pile direction is consistent for all stair pieces.
Goal: Prepare carpet sections for each stair tread and riser
What's used
Tools
- Carpet
- Measuring Tape Stanley
- Metal Straight Edge
- Utility Knife Roberts
About the full video
This DIY project provides a detailed guide on how to install carpet on a staircase, covering all necessary steps from preparing the stairs with tack strips and underlay to precisely cutting and securing the carpet. The process involves measuring, cutting, stapling, stretching, and tucking the carpet for a professional finish.
Step 2 of 7: Cut Carpet Treads to Size
Using your recorded measurements, cut the carpet material for each tread. The cut piece should match the tread depth and extend to cover the nosing. If your carpet has a backing, ensure you cut through both the carpet pile and the backing cleanly. For a clean edge, you might consider cutting slightly larger and then trimming to fit precisely in the next step.
Every video in How to Install Carpet Treads on Stairs with a Deep Nosing Overhang
Step 1: Measure Existing Tread Depth and Nosing
- 0:57–1:16 Measure Treads and Mark Laminate
- 0:46–1:05 Measure and Cut Underlayment
- 0:12–0:57 Measure and Cut Carpet Tread
Step 2: Cut Carpet Treads to Size
- 7:20–9:07 Measure and Cut Carpet
- 0:12–0:57 Measure and Cut Carpet Tread
- 2:09–3:19 Measure and Cut Carpet Pieces (this video)
Step 3: Dry Fit and Trim Carpet Treads
- 2:13–2:35 Test Fit and Adjust Treads
- 3:53–7:38 Trim Excess Carpet and Prepare Final Riser
- 0:57–2:36 Pre-form and Secure Carpet Underneath Tread
Step 4: Apply Adhesive to Treads
- 0:05–0:06 Apply Adhesive to Treads
- 0:34–0:46 Apply Carpet Adhesive to Stairs
- 0:16–0:21 Apply Peel-and-Stick Carpet Treads
Step 5: Install Carpet Treads
- 0:04–0:06 Install Carpet Treads
- 0:59–2:07 Install First Stair Tread
- 0:11–0:43 Install Remaining Carpet Stair Treads
Step 6: Secure Nosing Overhang
- 0:57–2:36 Pre-form and Secure Carpet Underneath Tread
- 1:19–1:59 Lay and Secure Carpet Sections (Repetitive)
- 12:05–14:25 Fold and Staple Carpet Over Next Nose
Step 7: Allow Adhesive to Cure
- 3:06–3:19 Project Completion
- 3:44–4:26 Final Curing and Caulking
- 0:31–0:38 Inspect and Finish Installation
How to Install Carpet Treads on Stairs with a Deep Nosing Overhang
This project outlines the steps for installing carpet treads on stairs that have a deep nosing overhang. It covers measuring, cutting, fitting, and securing the treads to ensure a safe and aesthetically pleasing result.
Read the full guide Browse all guides
Planning this project? Shop Oak Valley Designs.

