Install Remaining Carpet Stair Treads
From How to Install Carpet Treads on Stairs with a Deep Nosing Overhang · Step 5 of 7 · Video by Oak Valley Designs

Showing 0:11–0:43 of the source video. Watch the full video with every moment.
What happens in this clip
Once a tread is aligned, firmly press it down to secure it in place. The video implies an adhesive backing on the treads, as no other fastening method is shown. Repeat this process for the remaining stairs: place a new carpet tread, ensure it is centered and straight by visual inspection or quick checks with the tape measure against the previous tread or stair edge, and then firmly press it down to adhere. Continue this process for all steps on the staircase until all treads are installed.
Goal: Securely install all carpet treads on the staircase
What's used
Tools
- Carpet Stair Tread
- Hands
- Tape Measure Lufkin
- Ruler
About the full video
This project demonstrates the straightforward process of installing pre-cut carpet stair treads onto a wooden staircase. It focuses on careful measurement, alignment, and secure placement of each tread to enhance both the safety and aesthetic appeal of the stairs.
Step 5 of 7: Install Carpet Treads
With the adhesive applied, carefully align the carpet tread with the stair tread. Press down firmly, starting from the back and working towards the nosing, to ensure full contact and adhesion. Apply even pressure across the entire surface, especially along the edges and over the nosing, to eliminate any air bubbles and create a strong bond. Use a roller or your hands to press firmly.
Every video in How to Install Carpet Treads on Stairs with a Deep Nosing Overhang
Step 1: Measure Existing Tread Depth and Nosing
- 0:57–1:16 Measure Treads and Mark Laminate
- 0:46–1:05 Measure and Cut Underlayment
- 0:12–0:57 Measure and Cut Carpet Tread
Step 2: Cut Carpet Treads to Size
- 7:20–9:07 Measure and Cut Carpet
- 0:12–0:57 Measure and Cut Carpet Tread
- 2:09–3:19 Measure and Cut Carpet Pieces
Step 3: Dry Fit and Trim Carpet Treads
- 2:13–2:35 Test Fit and Adjust Treads
- 3:53–7:38 Trim Excess Carpet and Prepare Final Riser
- 0:57–2:36 Pre-form and Secure Carpet Underneath Tread
Step 4: Apply Adhesive to Treads
- 0:05–0:06 Apply Adhesive to Treads
- 0:34–0:46 Apply Carpet Adhesive to Stairs
- 0:16–0:21 Apply Peel-and-Stick Carpet Treads
Step 5: Install Carpet Treads
- 0:04–0:06 Install Carpet Treads
- 0:59–2:07 Install First Stair Tread
- 0:11–0:43 Install Remaining Carpet Stair Treads (this video)
Step 6: Secure Nosing Overhang
- 0:57–2:36 Pre-form and Secure Carpet Underneath Tread
- 1:19–1:59 Lay and Secure Carpet Sections (Repetitive)
- 12:05–14:25 Fold and Staple Carpet Over Next Nose
Step 7: Allow Adhesive to Cure
- 3:06–3:19 Project Completion
- 3:44–4:26 Final Curing and Caulking
- 0:31–0:38 Inspect and Finish Installation
How to Install Carpet Treads on Stairs with a Deep Nosing Overhang
This project outlines the steps for installing carpet treads on stairs that have a deep nosing overhang. It covers measuring, cutting, fitting, and securing the treads to ensure a safe and aesthetically pleasing result.
Read the full guide Browse all guides
Planning this project? Shop Oak Valley Designs.

