Test Fit and Adjust Treads
From How to Install Carpet Treads on Stairs with a Deep Nosing Overhang · Step 3 of 7 · Video by Dani Lyn Design

Showing 2:13–2:35 of the source video. Watch the full video with every moment.
What happens in this clip
Once a new stair tread has been cut, take it inside and test its fit on the corresponding stair. Place it gently into position to check for proper length and alignment. The presenter found that some of her cuts, made conservatively, were still slightly too long. If a tread doesn't fit perfectly, take it back to your cutting area and trim off just a tiny bit more to achieve a snug fit, then re-test.
Goal: Ensure each new stair tread fits perfectly before permanent installation.
What's used
Tools
- Circular Saw Ryobi
- New Stair Tread
About the full video
This DIY project provides detailed instructions on how to replace old, worn-out stair treads with new ones. The process covers everything from initial assessment and removal of existing treads to precise measurement, cutting, secure installation using adhesive and a nail gun, and finally, filling and sanding imperfections in preparation for staining.
Step 3 of 7: Dry Fit and Trim Carpet Treads
Place each cut carpet tread onto its intended stair to check the fit. Pay close attention to how it sits around the nosing and against the riser. Make any necessary small adjustments or trims to ensure the carpet lies flat and covers the tread area completely without bunching or leaving gaps. The goal is a precise fit that follows the contours of the stair.
Every video in How to Install Carpet Treads on Stairs with a Deep Nosing Overhang
Step 1: Measure Existing Tread Depth and Nosing
- 0:57–1:16 Measure Treads and Mark Laminate
- 0:46–1:05 Measure and Cut Underlayment
- 0:12–0:57 Measure and Cut Carpet Tread
Step 2: Cut Carpet Treads to Size
- 7:20–9:07 Measure and Cut Carpet
- 0:12–0:57 Measure and Cut Carpet Tread
- 2:09–3:19 Measure and Cut Carpet Pieces
Step 3: Dry Fit and Trim Carpet Treads
- 2:13–2:35 Test Fit and Adjust Treads (this video)
- 3:53–7:38 Trim Excess Carpet and Prepare Final Riser
- 0:57–2:36 Pre-form and Secure Carpet Underneath Tread
Step 4: Apply Adhesive to Treads
- 0:05–0:06 Apply Adhesive to Treads
- 0:34–0:46 Apply Carpet Adhesive to Stairs
- 0:16–0:21 Apply Peel-and-Stick Carpet Treads
Step 5: Install Carpet Treads
- 0:04–0:06 Install Carpet Treads
- 0:59–2:07 Install First Stair Tread
- 0:11–0:43 Install Remaining Carpet Stair Treads
Step 6: Secure Nosing Overhang
- 0:57–2:36 Pre-form and Secure Carpet Underneath Tread
- 1:19–1:59 Lay and Secure Carpet Sections (Repetitive)
- 12:05–14:25 Fold and Staple Carpet Over Next Nose
Step 7: Allow Adhesive to Cure
- 3:06–3:19 Project Completion
- 3:44–4:26 Final Curing and Caulking
- 0:31–0:38 Inspect and Finish Installation
How to Install Carpet Treads on Stairs with a Deep Nosing Overhang
This project outlines the steps for installing carpet treads on stairs that have a deep nosing overhang. It covers measuring, cutting, fitting, and securing the treads to ensure a safe and aesthetically pleasing result.
Read the full guide Browse all guides
Planning this project? Shop Oak Valley Designs.

