Prepare and Clean Stair Treads
From How to Install Carpet Treads on Stairs with an Open Side · Step 1 of 6 · Video by Oak Valley Designs

Showing 0:09–0:45 of the source video. Watch the full video with every moment.
What happens in this clip
Begin by thoroughly cleaning the stair treads. You can use a microfiber cloth or any suitable cloth, optionally combined with a handheld vacuum, to remove all dust and loose dirt. The goal is to ensure the entire stair surface is clean and completely dry. This is crucial for the adhesive on the back of the carpet treads to stick properly. Avoid using any cleaning products that might leave a greasy residue, such as Pledge or Pine-Sol, as this can compromise the adhesive bond.
Goal: Clean the entire surface of each stair tread to remove all dust and loose dirt, ensuring it is nice and dry for optimal adhesive bonding.
What's used
Tools
- Handheld vacuum
- Microfiber cloth
About the full video
This project provides step-by-step instructions for easily installing carpet treads onto stairs using strong adhesive tape. It covers preparing the stairs by cleaning them, marking alignment with painter's tape, and then securely attaching the self-adhesive carpet treads for a secure and streamlined look.
What's said in this clip
Hi everyone, it's Amy with Oak Valley Designs. I'm going to talk to you about cleaning your stairs in preparation for your new carpet stair treads. So, you can grab a microfiber cloth or any cloth really works. You can do a handheld vacuum or you can use both. And what I like to do is simply take the cloth, make sure you're wiping the entire stair tread, get all of the dust, all of the loose dirt off of here. And the idea is to keep it nice and dry so that the adhesive on the back of your stair tread will really stick nicely. Try to avoid using anything that'll make it greasy, like pledge or pine saw. And that's all
Automatically transcribed from the source video.
Step 1 of 6: Clean Stair Treads
Vacuum each stair tread to remove loose dirt and dust. Then, use a stiff brush and a mild cleaning solution (like diluted dish soap) to scrub away any embedded dirt or grime. For stubborn adhesive residue, a plastic scraper or a solvent-specific adhesive remover may be necessary. Rinse the treads with a damp cloth and allow them to dry completely before proceeding.
Every video in How to Install Carpet Treads on Stairs with an Open Side
Step 1: Clean Stair Treads
- 0:09–0:45 Prepare and Clean Stair Treads (this video)
- 0:34–0:40 Clean the Stairs
- 0:18–0:31 Clean the Stairs
Step 2: Measure and Mark Carpet Treads
- 0:12–0:57 Measure and Cut Carpet Tread
- 7:20–9:07 Measure and Cut Carpet
- 0:16–0:27 Measure and Cut Carpet Sections
Step 3: Cut Carpet Treads
- 8:08–9:23 Cut Carpet Pieces
- 0:12–0:57 Measure and Cut Carpet Tread
- 0:37–0:59 Measure and Cut Carpet
Step 4: Apply Adhesive
- 0:05–0:06 Apply Adhesive to Treads
- 0:34–0:46 Apply Carpet Adhesive to Stairs
- 0:33–0:39 Apply Adhesive and Lay First Pieces
Step 5: Install Carpet Treads
- 0:04–0:06 Install Carpet Treads
- 1:16–2:09 Install Carpet Treads with Adhesive
- 0:11–0:43 Install Remaining Carpet Stair Treads
Step 6: Trim Excess Carpet
- 1:28–2:59 Trim and Finish Edges
- 0:09–0:56 Trim Excess Carpet and Complete Installation
- 18:37–22:17 Trim and Tuck Side Edges
How to Install Carpet Treads on Stairs with an Open Side
A high-level outline for installing carpet treads on stairs with an open side. This involves preparing the stairs, cutting the carpet treads to size, and securely attaching them to the stairs, ensuring proper fit and adhesion, especially on the open side where additional care may be needed for a clean finish.
Read the full guide Browse all guides
Planning this project? Shop Oak Valley Designs.

