Layout Code-Compliant Winder Treads with Concentric Circles
From How to Lay Out Winder Stairs · Step 5 of 7 · Video by stairbuilding

Showing 6:31–8:31 of the source video. Watch the full video with every moment.
What happens in this clip
The video then illustrates a method for laying out winder treads using concentric circles and a framing square to achieve code-compliant uniform tread depths. It suggests drawing concentric circles from the inner corner of the winder. For a 90-degree corner, the lines radiating from the center of these circles to define the treads would be at angles (e.g., 45 degrees, 22.5 degrees). By ensuring the walk line (12 inches from the inside edge) follows a concentric curve, all treads measured along this path will have equal depth. This approach allows for creative and compliant winder designs.
What's used
Tools
- Framing Square
About the full video
This video provides a conceptual analysis of various winder stair layouts, emphasizing how to design them to comply with building codes, particularly regarding the 'walk line' and minimum tread measurements. It highlights why certain traditional winder designs are unsafe and demonstrates how to apply geometric principles, such as concentric circles, to create safe and code-compliant winder treads.
Step 5 of 7: Determine Winder Tread Layout
This is the most critical step for winder stairs. The layout involves creating a series of angled lines that represent the edge of each winder tread. The narrowest point of the winder tread (at the inside of the turn) must be at least 6 inches wide to meet code. The widest point (at the outside of the turn) will be determined by the overall stair width and the angle of the turn. Use geometry and precise measurements to ensure the tread's 'walking line' (typically 12 inches from the outer edge) has the required depth and that the tread is not excessively tapered. This often involves using a compass or string to draw arcs at the inner and outer edges of the turn.
Every video in How to Lay Out Winder Stairs
Step 1: Determine Total Rise and Run
- 2:54–4:34 Determine the Total Rise
- 0:16–1:17 Measure and Calculate Total Rise
- 0:04–0:30 Measure Total Rise
Step 2: Calculate Number of Treads and Risers
- 2:59–6:51 Calculate Number of Risers and Treads
- 8:59–9:54 Calculate Number of Risers and Treads
- 0:32–0:54 Calculate Number of Risers
Step 3: Determine Tread Depth and Landing Dimensions
Step 4: Layout the Stair Angle and Width
- 4:54–6:32 Lay Out Stringers
- 6:42–8:10 Lay Out the Stringer Using a Framing Square
- 0:11–1:48 Calculate and Layout Staircase Dimensions
Step 5: Determine Winder Tread Layout
- 8:11–8:46 Plan the L-Shaped Winder Staircase Design
- 6:31–8:31 Layout Code-Compliant Winder Treads with Concentric Circles (this video)
- 2:44–3:55 Designing Winder Treads with Angles
Step 6: Mark Stringers for Winder Treads
- 6:54–8:50 Marking Stringers
- 0:59–1:13 Mark First Step Cuts
- 1:28–2:15 Implement the Nosing Offset Adjustment
Step 7: Cut Stringers
- 9:35–10:04 Cut the Stringer
- 15:28–20:38 Cut Stringers
- 0:42–0:53 Cut the Stringers
How to Lay Out Winder Stairs
This project outlines the process for accurately laying out winder stairs, which feature wedge-shaped treads that turn a corner. The process involves careful measurement, mathematical calculations, and precise marking to ensure safety, code compliance, and aesthetic appeal.
Read the full guide Browse all guides
Planning this project? Shop Oak Valley Designs.

