Minimum Tread Depth and Landing Dimensions
From How to Lay Out Winder Stairs · Step 3 of 7 · Video by gregvancom

Showing 3:14–4:28 of the source video. Watch the full video with every moment.
What happens in this clip
Understand the minimum tread depth and landing dimensions. The minimum tread depth must be 10 inches (older codes allowed 9 inches). For stair landings, their depth must be equal to or larger than the width of the stairway itself. This rule applies to both the top and bottom landings. While historical codes sometimes specified a 36-inch minimum for landings, the current 2021 Residential Building Code emphasizes that the landing depth should match or exceed the stair width. It is advisable to consult your local building department if you have any questions or prefer alternative designs.
Goal: Achieve compliant tread depth and landing dimensions.
What's used
Tools
- International Residential Building Code Book (2021 version)
- Local building department resources
- Tape Measure
About the full video
This project offers a comprehensive guide for DIY enthusiasts on essential stair building codes based on the 2021/2022 International Residential Building Code. It systematically breaks down regulations concerning door swings over stairs, minimum stairway width, required headroom clearance, individual riser height limits, minimum tread depth, landing dimensions, allowable variations in riser and tread measurements, and exceptions for non-habitable attic and crawl space access. The goal is to provide a solid foundation of knowledge for planning and executing safe and compliant stair construction or renovation projects.
What's said in this clip
Next up the minimum tread depth will be ten inches. However, when I first started working, it was nine inches and the vertical riser height was eight inches. Next up, let's go ahead and take a look at the minimum width or depth of the stair landing itself. And according to these building codes, the depth of the stair tread will need to be the same or larger than the width of the stairway. And that would be the same for the top or the bottom. So the depth of this landing here will need to be the width of this or larger. And this was something a long time ago that used to have a 36 inch minimum, which would be the same as the minimum width for a stairway. However, they have changed the verbiage on it. So again, these building codes are from the 2021 residential building code book. And for the most part, these are building codes I like. However, if you do not like them, then check with your local building department to see if they have different building codes that might work better for your project or for you personally.
Automatically transcribed from the source video.
Step 3 of 7: Determine Tread Depth and Landing Dimensions
Using the total run available and the number of treads, calculate the nominal tread depth. Ensure this depth, when combined with the riser height, meets the '2R + T' rule (twice the rise plus the tread depth should be between 24 and 25 inches) for comfortable and safe walking. If a landing is required, ensure its dimensions meet code (typically at least as wide as the stair and as deep as the stair's run).
Every video in How to Lay Out Winder Stairs
Step 1: Determine Total Rise and Run
- 2:54–4:34 Determine the Total Rise
- 0:16–1:17 Measure and Calculate Total Rise
- 0:04–0:30 Measure Total Rise
Step 2: Calculate Number of Treads and Risers
- 2:59–6:51 Calculate Number of Risers and Treads
- 8:59–9:54 Calculate Number of Risers and Treads
- 0:32–0:54 Calculate Number of Risers
Step 3: Determine Tread Depth and Landing Dimensions
- 2:05–2:24 Calculate Individual Riser Height & Tread Depth
- 5:03–6:09 Determine Tread Overhang and Length
- 3:14–4:28 Minimum Tread Depth and Landing Dimensions (this video)
Step 4: Layout the Stair Angle and Width
- 4:54–6:32 Lay Out Stringers
- 6:42–8:10 Lay Out the Stringer Using a Framing Square
- 0:11–1:48 Calculate and Layout Staircase Dimensions
Step 5: Determine Winder Tread Layout
Step 6: Mark Stringers for Winder Treads
- 6:54–8:50 Marking Stringers
- 0:59–1:13 Mark First Step Cuts
- 1:28–2:15 Implement the Nosing Offset Adjustment
Step 7: Cut Stringers
- 9:35–10:04 Cut the Stringer
- 15:28–20:38 Cut Stringers
- 0:42–0:53 Cut the Stringers
How to Lay Out Winder Stairs
This project outlines the process for accurately laying out winder stairs, which feature wedge-shaped treads that turn a corner. The process involves careful measurement, mathematical calculations, and precise marking to ensure safety, code compliance, and aesthetic appeal.
Read the full guide Browse all guides
Planning this project? Shop Oak Valley Designs.

